yftsx 053a89013a sync: 2026-09-30 15:41:23 1 month ago
..
Res 053a89013a sync: 2026-09-30 15:41:23 1 month ago
lib 053a89013a sync: 2026-09-30 15:41:23 1 month ago
SHT30.lua 053a89013a sync: 2026-09-30 15:41:23 1 month ago
Update.lua 053a89013a sync: 2026-09-30 15:41:23 1 month ago
autoGPS.lua 053a89013a sync: 2026-09-30 15:41:23 1 month ago
config.lua 053a89013a sync: 2026-09-30 15:41:23 1 month ago
main.lua 053a89013a sync: 2026-09-30 15:41:23 1 month ago
readme.md 053a89013a sync: 2026-09-30 15:41:23 1 month ago
scd.lua 053a89013a sync: 2026-09-30 15:41:23 1 month ago
scdbf.lua 053a89013a sync: 2026-09-30 15:41:23 1 month ago
update32.lua 053a89013a sync: 2026-09-30 15:41:23 1 month ago
ymodem.lua 053a89013a sync: 2026-09-30 15:41:23 1 month ago
性诱III型通讯协议V3.md 053a89013a sync: 2026-09-30 15:41:23 1 month ago

readme.md

2024-12-21

ymodem.lua 249行 if not sd:len() then break end 修复STM32升级异常问题

2024-3-26

增加远程修改设备光控状态功能 方便修改设备工作状态 function Light_control_handoff()

local Light_control1 = string.char(0xAA,0x03,0x01)
local Light_control2 = string.char(0xAA,0x03,0x00)
while true do 
    if result.lcm == 0 then
        uart.write(1,Light_control1)
    elseif result.lcm == 1 then
        uart.write(1,Light_control2)
    end
    return
end
log.info("Light control handoff begin!!!!")

end

elseif cnf.cmd == "Light_control_handoff" then -- 光控模式切换 Light_control_handoff() --光控模式切换 if not mqttc:publish(pub, upres("Light_control_handoff", "The light control mode was successfully switched!!"), serverconf.qos) then break end

2024-2-23

修改串口通讯心跳逻辑 调整上报数据频率为5S一次 心跳间隔为1分钟 离线后开机间隔间隔为两分半 sys.taskInit(

function()
    sys.wait(100)
    local uart_flag_count = 0
    local uart_32 = string.char(0xCC,0XDD)
    while true do
        if uart_flag == 1 then
            uart_flag = 0
            uart_flag_count = uart_flag_count + 1
            if uart_flag_count > 5 then
                uart_flag_count = 0
                uart.write(1,uart_32)
                log.info("uart_flag back!!!!")
            end
        end
        sys.wait(50)
    end
end

)

2024-1-30

新增远程升级分类操作升级后可更新flash内数据

--参数更新升级 function update_stm32_parameters()

local update32 = string.char(0xCC,0xAA)
while true  do
    uart.write(1,update32)
    sys.wait(500)
end
log.info("update_stm32_parameters begin!!!!")

end

elseif cnf.cmd == "update_stm32_Parameter" then -- stm32 升级 开始

if not mqttc:publish(pub, upres("update_stm32_Parameter", "stm32 update will start!!"), serverconf.qos) then break end
update_stm32_parameters()
sys.wait(200)
stm8_update_sw = 1
update_stm32() --STM32远程升级

2024-1-25

新增串口通讯心跳相关代码 --串口通讯交互心跳标志位 local uart_flag = 0

--串口通讯心跳交互 sys.taskInit(

function()
    sys.wait(100)
    local uart_32 = string.char(0xCC,0XDD)
    while true do
        if uart_flag == 1 then
            uart_flag = 0

            uart.write(1,uart_32)
            log.info("uart_flag back!!!!")
        end
        sys.wait(50)
    end
end

)

if flowCount[1] == 64 then --串口通讯心跳检测

    uart_flag = 1
end

2023-12-18

修改串口通讯解析内容,消除主板温度不能负值参数 idx, result.bt = pack.unpack(conf, "<h", idx) -- 主板温度

2023-11-17

增加上报新字段vps 电压状态欠压过压

线程之外不能使用sys.wait()延时函数

函数中使用sys.wait()延时函数,在线程调用可以使用 ,但要注意相互引用

2023-11-27

增加光控模式切换变量 增加相关操作代码

2023-11-18

修改平台下发交互部分代码 删除下发相关函数中的延时函数防止后续调用报错

2023-11-13

增加上报新字段vps 电压状态欠压过压

2023-10-25

修改高压计数字段单片机上报判断条件为 if(result_crc.kcnt>0 and result_crc.kcnt<9000) then result.kcnt = result_crc.kcnt end 修改高压计数字段平台上报判断条件为 if tonumber(data.ct) > 5000 then

    data.ct = "0"
end

2023-10-23

修改高压计数上报部分的代码 消除了上报数值不能超过25的异常问题 之前原因为浮点数为作为判断条件导致无法出现超过25的数值 由 data.ct = string.format(result.kcnt) -- 电击次数

if data.ct > "255" then
    data.ct = "0"
end

改为 data.ct = string.format(result.kcnt) -- 电击次数

if tonumber(data.ct) > 255 then
    data.ct = "0"
end  

2023-9-28

修改自清虫部分代码,有下位机进行控制 -- 清虫任务: sys.taskInit(function()

sys.wait(20 * 1000)
if not VERSION:find("ZQC") then
    log.error("not zqc devices!!!")
    return
end
if zqcflag == 0 then
    log.info("first")
    local cle_cnt = 0
    local dat_freq = string.char(0xAA,0x07)
    while true  do
        log.info("second")
        cle_cnt = cle_cnt + 1
        log.info("自清虫模式设置成功")
        uart.write(1,dat_freq)
        sys.wait(500)
        --uart.write(1,data)
        if cle_cnt == 2 then
        break end
    end
    log.info("自清虫模式设置结束")
end

end)

2023-9-14

更改设备主题用于区分迭代前后不同版本设备 新主题为/yfkj/scd-2.0/sub/

    /yfkj/scd-2.0/pub/

新增if result.ver:find("SCD-") then 判断不同版本程序 修改STN32远程升级判断条件及路径为 判断条件:SCD_STM32_UPDATE 路径:update/scd bin/rtthread.rbl 修改平台下发命令预警信息上报为组合信息

2023-8-25

增加平台交互预警信息平台下发设置后会有预警消息

elseif cnf.cmd == "paramconf" then -- 参数配置 -- Set_paramconf(packet.payload) -- sys.wait(1000) -- if not mqttc:publish(pub, upData(), serverconf.qos) then break end

-- 下发设备时控配置 if cnf.ext.ts ~= nil and cnf.ext.ts ~= '' and cnf.ext.st ~= nil and cnf.ext.st ~= '' and cnf.ext.et ~= nil and cnf.ext.et ~= '' then

log.warn("Set TimControl successful !!!!!!")
setsw(1)
SetTimControl(tonumber(cnf.ext.ts),tonumber(cnf.ext.st),tonumber(cnf.ext.et))
if not mqttc:publish(pub, upres("SCD-TimControl", "TimControl is"..cnf.ext.st..cnf.ext.et), serverconf.qos) then break end
sys.wait(100)

end -- 下发配置设备自清虫间隔 if cnf.ext.clt ~= nil and cnf.ext.clt ~= '' then

log.warn("Set Cleartime successful !!!!!!")
SetCleartime(tonumber(cnf.ext.clt))
if not mqttc:publish(pub, upres("SCD-Cleartime", "Cleartime is"..cnf.ext.clt), serverconf.qos) then break end
sys.wait(100)

end -- 下发配置设备数据上传时间间隔 if cnf.ext.dattim ~= nil and cnf.ext.dattim ~= '' then

log.warn("Set Dattim successful !!!!!!")
setDattim(tonumber(cnf.ext.dattim))
if not mqttc:publish(pub, upres("SCD-Dattim","Dattim is"..cnf.ext.dattim), serverconf.qos) then break end
sys.wait(100)

end -- 下发配置设备开关机 if cnf.ext.ds ~= nil and cnf.ext.ds ~= '' then

log.warn("Set switch successful !!!!!!")
setsw(tonumber(cnf.ext.ds))
if not mqttc:publish(pub, upres("SCD-switch","switch is"..cnf.ext.ds), serverconf.qos) then break end
sys.wait(100)

end -- 下发配置光控工作时长 if cnf.ext.tt ~= nil and cnf.ext.tt ~= '' then

log.warn("Set Timer successful !!!!!!")
setTimer(tonumber(cnf.ext.tt))
if not mqttc:publish(pub, upres("SCD-Timer", "Timer is"..cnf.ext.tt), serverconf.qos) then break end
sys.wait(100)

end --配置杀虫灯版本号 if cnf.ext.vt ~= nil and cnf.ext.vt ~= '' and type(cnf.ext.vt)=="string" then

nvm.set("version",cnf.ext.vt)
sys.restart(cnf.ext.vt)
if not mqttc:publish(pub, upres("SCD-version", "version is"..cnf.ext.vt), serverconf.qos) then break end
sys.wait(100)

end

2023-8-18

增加STM32远程升级成功上报功能 ymodem.lua local s = upwarn("update_stm32", "stm32 system update is ok!!") --平台上报升级成功消息 sys.publish("NET_SENTRDY", s) 增加升级失败重新升级

2023-7-11

增加autoGPS.lua 更新lib库为820版本 修改GPS自动切换相关的代码

local function test1Cb(tag)

log.info("testGps.test1Cb",tag)
printGps()

end

local function test2Cb(tag)

log.info("testGps.test2Cb",tag)
printGps()

end

local function test3Cb(tag)

log.info("testGps.test3Cb",tag)
printGps()

end

--测试代码开关,取值1,2 local testIdx = 1 local function test(idx)

--第1种测试代码
if idx==1 then
    --执行完下面三行代码后,GPS就会一直开启,永远不会关闭
    --因为gps.open(gps.DEFAULT,{tag="TEST1",cb=test1Cb}),这个开启,没有调用gps.close关闭
    gps.open(gps.DEFAULT,{tag="TEST1",cb=test1Cb})

    --10秒内,如果gps定位成功,会立即调用test2Cb,然后自动关闭这个“GPS应用”
    --10秒时间到,没有定位成功,会立即调用test2Cb,然后自动关闭这个“GPS应用”
    gps.open(gps.TIMERORSUC,{tag="TEST2",val=10,cb=test2Cb})

    --300秒时间到,会立即调用test3Cb,然后自动关闭这个“GPS应用”
    gps.open(gps.TIMER,{tag="TEST3",val=300,cb=test3Cb})
--第2种测试代码
elseif idx==2 then
    --执行完下面三行代码打开GPS后,5分钟之后GPS会关闭
    gps.open(gps.DEFAULT,{tag="TEST1",cb=test1Cb})
    sys.timerStart(gps.close,300000,gps.DEFAULT,{tag="TEST1"})
    gps.open(gps.TIMERORSUC,{tag="TEST2",val=10,cb=test2Cb})
    gps.open(gps.TIMER,{tag="TEST3",val=60,cb=test3Cb})
end

end


local function nmeaCb(nmeaItem)

log.info("testGps.nmeaCb",nmeaItem)

end

-- GPS+LBS定位任务 sys.subscribe("AUTOGPS_READY",function(gpsLib,agpsLib,kind,baudrate)

gps=gpsLib
agps=agpsLib
log.info("testGps.AUTOGPS_READY",baudrate,kind)
gps.setUart(uartId,baudrate,8,uart.PAR_NONE,uart.STOP_1) -- 设置串口通信参数,波特率为自适应
--gps.setAerialMode(1,1,0,0)  -- 设置GPS+BD定位(此接口目前仅针对Air530或者Air800有效)
gps.setNmeaMode(2,nmeaCb)   -- gps.lua和外部程序都处理NEMA数据
test(testIdx)
sys.timerLoopStart(printGps,2000)    

end)

sys.taskInit(

function()
    while true do
        gps_status = 0
        locat_cnt = 0 
        sys.wait(8 * 1000)          -- 等待socket连接完毕
        while true do
            if  tonumber(manual_location.type) == 0 then   -- 判断是否手动定位 若手动定位直接关闭GPS
                if socket.isReady() and gps_status ~=1 and gps_status ~= 2 then
                    log.warn("================ LBS Location successful ===============")
                    lbsLoc.request(getLocCb)
                    sys.wait(1000)
                end
                if gps.isFix() == false then
                    log.info("================ GPS Location failed ===============")
                    printGps()
                elseif gps.isFix() == true then
                    gps_cont = gps_cont + 1      
                    local location = gps.getLocation()
                    gps_loc_lat = location.lat
                    gps_loc_lng = location.lng
                    printGps()
                    if gps_cont >= 3 then   -- 获取3次gps定位数据的最后一次
                        nvm.set("lat_gps",gps_loc_lat)
                        nvm.set("lng_gps",gps_loc_lng)
                        gps.closeAll()
                    end
                    gps_status = 1
                    log.info("================ GPS Location successful ===============")
                end
                sys.wait(1000)
                log.info("GPS open status is:", gps.isOpen())
                log.info("GPS location status is:", gps.isFix())
            else
                gps_status = 0
                gps.closeAll()
                sys.wait(2000)
            end
            sys.wait(1000)
            locat_cnt = locat_cnt + 1 
            if locat_cnt >= 1800 then    -- 每隔30分钟判断一下定位,若失败,则break
                if (gps_loc_lng == "0" and gps_loc_lat == "0") and (lbs_loc_lat == "0" and lbs_loc_lng == "0") then
                    break 
                else 
                    locat_cnt = 0
                    log.warn("location normal !!!")
                end
            end 
        end
    end 
end 

)

2023-5-31

PROJECT = "SCD_4G_MODULE" VERSION = "4.0.02-3-4G-uart" 新增迭代版本单片机远程升级功能 增加update32.lua ymodem.lua 文件 通讯频率9600 传输字节128 及升级相关代码

--下发主板升级命令 function update_stm32()

local update_cnt = 0
local up_date_32 = string.char(0xAA,0xA0)
while true  do
    update_cnt = update_cnt + 1
    uart.write(1,up_date_32)
    sys.wait(500)
    if update_cnt == 2 then break end
end
log.info("update_stm32 begin!!!!")

end --下发BootLoader交互命令 function BootLoader_stm32()

local boot_count = 0
local BootLoader_32 = string.char(0x31)
while true do
    boot_count = boot_count + 1
    uart.write(1,BootLoader_32)
    sys.wait(200)
    if boot_count == 2 then break end
end   
log.info("BootLoader begin!!!!")

end

elseif cnf.cmd == "update_stm32" then

                        if not mqttc:publish(pub, upres("update_stm32", "stm32 update will start!!"), serverconf.qos) then break end
                        stm8_update_sw = 1
                        update_stm32() --STM32远程升级

--BootLoader交互信息下发 sys.taskInit(

function()
    sys.wait(500)
    while true do
        if BootLoader_flag == 1 then
            BootLoader_flag = 0
           log.info("BootLoader_flag",BootLoader_flag)
           BootLoader_stm32()
           log.info("stm32 SerialDownload !!!") 
        end
        if upgrade_again = 1 then
            log.info("update_stm32 system will upgrade again !!!")
            update32.run() 
        end
    sys.wait(500)
    end
end

)

if s:find("update") then

    updateflag = 1
    if update32.updateok == 0 then
        s = upwarn("device_stm32", "system will update")
        sys.publish("NET_SENT_RDY_", s)
    else
        s = upwarn("device_stm32", "system is updating......")
        sys.publish("NET_SENT_RDY_", s)
    end
    log.info("update_stm32 system will update !!!")
    update32.run()
end

新增STM32单片机通讯代码

----------DCSCD--U-V1.0版本

elseif #conf == nil or #conf == 0 or conf:len() == 62 then 
    log.info("getParam len,value:", string.toHex(conf, " ")) -- 将返回的数据填充到result表
    result.ver = string.sub(conf, 47,59)                -- 软件版本-DC-SCD-U-V1.0

    idx, result.iSave = pack.unpack(conf, "b", idx)          -- eeprom标志位
    if result.iSave ~= 0xAA then return end                  -- 判断chuankou上传数据格式是否正确

    idx, result_crc.ds = pack.unpack(conf, ">b", idx)            -- 设备状态
    if(result_crc.ds==0 or result_crc.ds==1) then result.ds = result_crc.ds end

    idx, result_crc.tt = pack.unpack(conf, "b", idx)             -- 光控时长小时
    if(result_crc.tt>=0 and result_crc.tt<8) then result.tt = result_crc.tt end 

    idx, result_crc.ws = pack.unpack(conf, "b", idx)             -- 工作状态
    if(result_crc.ws==0 or result_crc.ws==1 or result_crc.ws==2) then result.ws = result_crc.ws end

    idx, result_crc.lps = pack.unpack(conf, "b", idx)            -- 光控状态
    if(result_crc.lps==0 or result_crc.lps==1) then result.lps = result_crc.lps end

    idx, result_crc.rps = pack.unpack(conf, "b", idx)            -- 雨控状态
    if(result_crc.rps==0 or result_crc.rps==1) then 
        result.rps = result_crc.rps 
        if(result_crc.rps==1 and rps_y==0) then
            rps_x = 1
        elseif(result_crc.rps==0) then
            rps_y = 0 
        end
    end
    idx, result_crc.tps = pack.unpack(conf, "b", idx)          -- 温控状态
    if(result_crc.tps==0 or result_crc.tps==1 or result_crc.tps==2) then result.tps = result_crc.tps end

    idx, result_crc.dps = pack.unpack(conf, "b", idx)          -- 倾倒保护
    if(result_crc.dps==0 or result_crc.dps==1) then result.dps = result_crc.dps end

    idx, result_crc.vps = pack.unpack(conf, "b", idx)        -- 电压状态

    if(result_crc.vps==0 or result_crc.vps==1 or result_crc.vps==2) then result.vps = result_crc.vps end

    idx, paramconf.battype = pack.unpack(conf, "b", idx)     -- 电池类型

    idx, result.Lamp = pack.unpack(conf, 'b', idx)          --  灯管故障检测

    idx, result.Infrared = pack.unpack(conf, 'b', idx)      --  红外传感器

    idx, result.kcnt = pack.unpack(conf, "b", idx)     -- 电击击杀检测
    --if(result_crc.kcnt>0 and result_crc.kcnt<255) then result.kcnt = result_crc.kcnt end

    idx, result.cleartim = pack.unpack(conf, 'b', idx)      -- 清虫时间间隔

    idx, result.cycle_on = pack.unpack(conf, 'b', idx)     -- 放电前频率
    idx, result.cycle_off = pack.unpack(conf, 'b', idx)    --放电结束频率

    idx, result_crc.cv = pack.unpack(conf, "<H", idx)       -- 充电电压
    if(result_crc.cv>0 and result_crc.cv<30000) then
         result.cv = result_crc.cv 
         if result.cv < 500 then
            result.cv = 0
         end 
    end
    idx, result_crc.bv = pack.unpack(conf, "<H", idx)            -- 电池电压
    if(result_crc.bv>0 and result_crc.bv<30000) then result.bv = result_crc.bv end

    idx, result.bt = pack.unpack(conf, "<H", idx)            -- 主板温度

    idx, paramconf.vsunrise = pack.unpack(conf, "<H", idx)   -- 日出电压
    idx, paramconf.vsunset = pack.unpack(conf, "<H", idx)    -- 日落电压
    idx, paramconf.vcutof = pack.unpack(conf, "<H", idx)     -- 充电截至电压
    idx, paramconf.vfloat = pack.unpack(conf, "<H", idx)     -- 充电浮充电压
    idx, paramconf.vrecharge = pack.unpack(conf, "<H", idx)  -- 再次启动充电动作的电压
    idx, paramconf.vstart = pack.unpack(conf, "<H", idx)     -- 首次启动电压
    idx, paramconf.uvoff = pack.unpack(conf, "<H", idx)      -- 欠压解锁电压
    idx, paramconf.uvon = pack.unpack(conf, "<H", idx)       -- 欠压锁定电压
    idx, paramconf.overtemp = pack.unpack(conf, "<H", idx)    -- 高温保护
    idx, paramconf.lowtemp = pack.unpack(conf, "<H", idx)     -- 低温保护
    idx, paramconf.unovert = pack.unpack(conf, "<H", idx)     -- 高温解锁
    idx, paramconf.unlowt = pack.unpack(conf, "<H", idx)      -- 低温解锁

    --idx, result.ver = pack.unpack(conf, 'c', idx)                -- 软件版本-DC-SCD-U-V1.0
    return result
end

2023-03-11

PROJECT = "SCD_4G_MODULE" VERSION = "4.0.02-1-4G-uart" 修改测试雨控状态改变数据上报 定义新增变量两个 rps_x rps_y if(result_crc.rps==0 or result_crc.rps==1) then

        result.rps = result_crc.rps 
        if(result_crc.rps==1 and rps_y==0) then
            rps_x = 1
        elseif(result_crc.rps==0) then
            rps_y = 0 
        end

end

    --雨控即时上报

sys.taskInit(

function()
    sys.wait(1000)
    while true do
        if rps_x == 1  then
            updata_freq = 0
            rps_x = 0
            rps_y = 1
        end 
   sys.wait(1000)
   end     
end

)

2023-01-04

修复四情平台status不实时更新问题 PROJECT = "SCD_4G_MODULE" VERSION = "4.0.02-4G-uart"

2022-09-14

VERSION = "4.0.01-4G-uart" 修复充电后工作时充电有残余电压

2022-07-22

PROJECT = "SCD_4G_MODULE"
VERSION = "4.0.0-4G-uart"

更新说明:

  • 1.增加双平台切换: {"cmd": "platform", "ext": {"type": "120.27.222.26"}} {"cmd": "platform", "ext": {"type": "8.136.98.49"}}
  • 2.温湿度及定位信息保存到flash,开机在定位失败或者未收到温湿度数据时读取;
  • 3.增加stm8主板:重启预警,高压频率解析;
  • 4.开机预警信息:固件版本,启动信息;

{"cmd": "paramconf", "ext": {"vt": "ZQC"}}

2022-02-19

PROJECT = "SCD_4G_MODULE"
VERSION = "3.3.20-uart-4G-LIGHT"
  • 更新说明:不再主动获取stm8主板状态;

2022/1/20

程序优化 增添IIC上传数据参数异常判断处理避免异常数据上报

idx, result_crc.ds = pack.unpack(conf, ">b", idx) -- 设备状态

if(result_crc.ds==0 or result_crc.ds==1) then result.ds = result_crc.ds end

idx, result_crc.tt = pack.unpack(conf, "b", idx)             -- 光控时长小时
if(result_crc.tt>=0 and result_crc.tt<8) then result.tt = result_crc.tt end 

idx, result_crc.ws = pack.unpack(conf, "b", idx)             -- 工作状态
if(result_crc.ws==0 or result_crc.ws==1 or result_crc.ws==2) then result.ws = result_crc.ws end

idx, result_crc.lps = pack.unpack(conf, "b", idx)            -- 光控状态
if(result_crc.lps==0 or result_crc.lps==1) then result.lps = result_crc.lps end

idx, result_crc.rps = pack.unpack(conf, "b", idx)            -- 雨控状态
if(result_crc.rps==0 or result_crc.rps==1) then result.rps = result_crc.rps end

idx, result_crc.tps = pack.unpack(conf, "b", idx)            -- 温控状态
if(result_crc.tps==0 or result_crc.tps==1 or result_crc.tps==2) then result.tps = result_crc.tps end

idx, result_crc.dps = pack.unpack(conf, "b", idx)            -- 倾倒保护
if(result_crc.dps==0 or result_crc.dps==1) then result.dps = result_crc.dps end

idx, result_crc.vps = pack.unpack(conf, "b", idx)            -- 电压状态
if(result_crc.vps==0 or result_crc.vps==1) then result.vps = result_crc.vps end

idx, result.cv = pack.unpack(conf, ">I", idx)                -- 充电电压
if(result_crc.cv>0 and result_crc.cv<30000) then result.cv = result_crc.cv end

idx, result_crc.bv = pack.unpack(conf, ">I", idx)            -- 电池电压
if(result_crc.bv>0 and result_crc.bv<30000) then result.bv = result_crc.bv end

idx, result.bt = pack.unpack(conf, ">I", idx)            -- 主板温度
--if(result_crc.bt>-40 and result_crc.bt<100) then result.bt = result_crc.bt end

功能升级 添加反向订阅平台端天气接口功能,避免MQTT对接温湿度为默认值

--//--------反向获取平台温湿度接口传回MQTT function Setsensor_value(dat_sensor)

local cmds,result,err = json.decode(dat_sensor)
if not result then
   return
end
if cmds.ext.new_hum~=nil and cmds.ext.new_hum~="" then
    if tonumber(cmds.ext.new_hum)>=0 and tonumber(cmds.ext.new_hum)<=100 then
        hum = tonumber(cmds.ext.new_hum)
    end
end
if cmds.ext.new_tem~=nil and cmds.ext.new_tem~="" then
    if tonumber(cmds.ext.new_tem) < 100 then
        temp = tonumber(cmds.ext.new_tem)
    end
end
log.warn(">>>>>>>>>sensor data get is:>>>>>>>>>>",hum,temp)

end

elseif result and cnf.cmd=="sensor" then Setsensor_value(packet.payload)

elseif result and cnf.cmd=="sensor" then

Setsensor_value(packet.payload)


--==== 版本1:物联网(不带光控) === PROJECT = "SCD_4G_MODULE" VERSION = "3.3.19-4G"

bug 修复 448行 在scd.lua 的448行添加 if st1==nil or st1=="" or et1 ==nil or et1 == "" then return end

消除定时时间设置为空的参数传递错误

2021 08 18 bug修复 scd文件 353行
上传数据信息
将 data.ds = string.format(result.ws or 1) -- 设备是否开机 更改为 data.ds = string.format(result.ds or 1) -- 设备是否开机

bug修复 远程升级函数调用重复 将lib库中的update.lua 文件删除

版本 3.3.18

2021 08 15 bug 修复 scd 文件 1234行
mqtt2线程守护线程
将if thirdserverconf.ip == "" then 更改为if thirdserverconf == nil or thirdserverconf.ip == "" then