---scd--@module testSocket--@author 稀饭放姜--@license MIT--@copyright hnyfkj.com--@release 2017.9.27 require "socket" require "misc" require "led" require "mqtt" require "lbsLoc" require "pins" require "autoGPS" -- utoGPS功能模块只能配合Air820使用;如果不是这款模块,不要打开agps功能 require "ril" require "Update" require "sim" ------------------------------ require "config" --默认参数保存 require "nvm" module(..., package.seeall) -- 本地存储文件 local DEVICE_CONF = "/device.conf" local SERVER_CONF = "/server.conf" local DATTIM_CONF = "/dat_f.conf" local DEV_REBOOT = "/rebootmes.txt" local PRARM_CONF = "/prarm.conf" local CONTROL_CONF = "/control.txt" local THIRD_CONF = "/thirdconf.conf" --第三方服务器数据保存 local SHT30_DATA = "/sht30data.conf" --温湿度参数保存 local GPS_CONF = "/gps.conf" --保存GPS定位数据 -- 上报json数据的基础表 local message = {cmd = "", ext = {}} -- 上报遗言的json表 local willmsg = {cmd = "offline", ext = {imei = ""}} -- 温湿度天气接口的值 local temp, hum -- GPIO 输入检测 pmd.ldoset(2, pmd.LDO_VLCD) -------红外计数------ local infrared_count = 0 --------------------------MQTT定时数据上报---------------------------- local mqtt_status = "true" local mqtt_status_num = 0 local timeout = 1 local updata_freq = 0 --------------------------------------------------------------------- --------------------------物联网模块重启-------------------------- -- 重启标志 local rebootstate -- 重启次数 local rebootcnt -- 重启信息 local rebootinfo = 1 --1:正常 2:socket重连 3:MQTT重连 ---------------------------------------------------------------- -- 清虫时间间隔 local dat_f = 10 -- 上报数据时间间隔 local clt_t = 30 local wsflag = 0 local worktim = 0 -- 光控模式状态标志位 local clps = 0 --雨控即时上报标志位 local rps_x = 0 local rps_y = 0 ----------------------主板远程升级交互参数---------- --置位BootLoader交互下发标志位 --全局变量定义参数 updateflag = 0 --BootLoader进入升级模式标志位 BootLoader_flag = 0 --BootLoader交互下发标志位 upgrade_again =0 --STM32固件升级再次升级标志位 bootend = 0 --STM32固件升级完成标志位 local uart_flag = 0 --串口通讯交互心跳标志位 stm8_update_sw = 0 --主板升级一键测试防误触 ------------------------------------------------- ---------------------MQTT1---------------------- -- 检测是否分配到ip次数 local err_num = 0 -- TCP重连次数 local tcp_cont = 0 -- TCP连接正常的情况下,MQTT重订阅次数 local sub_cont = 0 -- mqtt1协程守护变量 local mqtt1_cont = 1 * 60 * 60 -- 超时时间1小时 ----------------------MQTT2--------------------- -- 检测是否分配到ip次数 local err2_num = 0 -- TCP重连次数 local tcp2_cont = 0 -- mqtt2协程守护变量 local mqtt2_cont = 1 * 60 * 60 -- 超时时间1小时 ---------------------------------------------- -- 时控参数配置 local timcontrl = { type = "", timctrl = 0, --时控开关 0-关 1开 默认:时控关闭 st = 20, --时控开始时间 默认:时间控制从半夜20点开始 et = 2 --时控结束时间 默认:时间控制到次日2点结束 } -- 配置参数保存基础表 local paramtable = { cmd = "paramconf", ext = { power = {ds = 1}, -- 配置开关机状态 work_tim = {timctrl = 0, st = 20, et = 2}, -- 配置定时控制模式 data_tim = {dat_f = 10}, -- 配置数据上报时间间隔 clt_tim = {clt_t = 30}, -- 配置清虫时间间隔 } } -- -------------------------定位------------------------- -- LBS经纬度 local lbs_loc_lat local lbs_loc_lng -- GPS经纬度 local gps_loc_lat local gps_loc_lng -- 定位状态 local gps_status = 0 -- 初始值0 local locat_cnt = 0 local gps,agps local uartId=3 -- GPS定位次数(处理GPS模块返回数据次数) local gps_cont = 0 -- 手动定位数据调度基础表 BD-09(百度坐标)-->不用坐标转换 local manual_location = {lat = "0", lng = "0", type = "0"} -- ------------------------------------------------------ -- MQTT1服务器配置表 serverconf = { imei = "", -- 唯一ID ip = "8.136.98.49", port = 61883, -- MQTT服务端口 sub = "/yfkj/xycb/s2c/", -- 服务器到客户端 -- 注意pub和sub后带" /" ,以便设备自动拼接imei pub = "/yfkj/xycb/c2s/", -- 客户端到服务器 lastwill = "/yfkj/xycb/offline/", -- 离线消息主题(部分)-->设备异常中断时用于mqtt服务器发布该设备的遗愿消息,个人网站客户端需订阅 sub1 = "yfkj/xycb/s2c/", pub1 = "yfkj/xycb/c2s/", lastwill1 = "yfkj/xycb/offline/", keepalive = 60, -- 心跳保持时间 uid = "user", -- 用户名 pwd = "f335bf402c655ee5fd2b5300905124e", -- 密码 qos = 0 } -- MQTT2服务配置表,用于设备对接 thirdserverconf = { imei = "", -- 唯一ID ip = "", port = 1883, sub = "/yfkj/xycb/s2c/", pub = "/yfkj/xycb/c2s/", keepalive = 60, lastwill = "/yfkj/xycb/offline/", uid = "", pwd = "", qos = 0 } -- 设备运行上报下发参数表 local paramconf = { imei = "", -- 唯一ID tt = 0, -- 默认光控定时模式下定时时常0小时 vsunrise = 6000, -- 日出电压 vsunset = 1500, -- 日落电压 lcm = 0, -- 光控类型 0太阳能板光控 1光敏二极管光控 vstart = 12000, -- 首次启动电压 uvon = 11500, -- 电池欠压锁定电压 uvoff = 12500, -- 电池欠压解锁电压 vrecharge = 12800, -- 再次启动充电动作的电压 vfloat = 13600, -- 电池浮充电压 vcutof = 14400, -- 电池充电截至电压 overtemp = 700, -- 高温保护阀值 lowtemp = 100, -- 低温保护阀值 unovert = 500, -- 高温解锁阀值 unlowt = 150, -- 低温解锁阀值 stamp = "20180301211805" -- 时间戳 } --主板参数配置 scdParam = { cmd = "Set_scdparam", ext = { lcm = 0, -- 光控类型 0太阳能板光控 1光敏二极管光控 vsunrise = 1500, --日落电压 vsunset = 6000, --日出电压 vcutof = 14400, --最高充电电压 vfloat = 13600, --恒压触发电压(浮充/恒压) vrecharge = 12800, --充电回滞电压 uvstart = 12000, --开机电压 uvoff = 12500, --放电迟滞电压 uvon = 11500, --过放保护电压 overtemp = 700, --高温保护电压 lowtemp = 100, --低温保护电压 unovert = 500, --高温解除电压 unlowt = 150 --低温解除电压 } } --串口接收检验 result_crc = { ds = 1, --设备开启状态 1:开 0:关 tt=4, -- 光控定时模式下定时时常(1--7)小时 ws = 0, -- 工作状态 0 待机,1工作,2充电 lps = 0, --光控状态 1:0 rps = 0, --雨控保护状态 1:0 tps = 0, --温度保护状态 1:0 dps = 0, --倾倒保护状态 1:0 bt = 0, --主板温度 kcnt = 0, -- 风机状态 cv = 0, --充电电压 xx.x ci = 0, --充电电流 x.xx bv = 12000, --电池电压 xx.x wv = 12, --工作电压 xx.x wi = 0, --工作电流 x.xx ver = "0", --e2prom版本 cycle_off = 0, --未放电时检测到的频率 clear_on = 0, --自清虫标志位 cleartim = 30,--清虫定时时间 Lamp = 0,--灯管故障检测 Infrared = 0--红外传感器 } --串口接收缓存 result = { ds = 1, --设备开启状态 1:开 0:关 tt=4, -- 光控定时模式下定时时常(1--7)小时 ws = 0, -- 工作状态 0 待机,1工作,2充电 lps = 0, --光控状态 1:0 rps = 0, --雨控保护状态 1:0 tps = 0, --温度保护状态 1:0 dps = 0, --倾倒保护状态 1:0 bt = 0, --主板温度 kcnt = 0, -- 风机状态 cv = 0, --充电电压 xx.x ci = 0, --充电电流 x.xx bv = 12000, --电池电压 xx.x wv = 12, --工作电压 xx.x wi = 0, --工作电流 x.xx cycle_off = 0, --未放电时检测到的频率 clear_on = 0, --自清虫标志位 ver = "0", cleartim = 30,--清虫定时时间 Lamp = 0,--灯管故障检测 Infrared = 0--红外传感器 } local function packAndSend(fid, value, multiplier) local scaledValue = (multiplier or 1) * value local highByte = bit.rshift(scaledValue, 8) local lowByte = bit.band(scaledValue, 0xFF) local command = string.char(0xDD, fid, highByte, lowByte) uart.write(1, command) sys.wait(400) end local function SetStatus() packAndSend(fid.vsunrise, scdParam.vsunrise) packAndSend(fid.vsunset, scdParam.vsunset) packAndSend(fid.vcutof, scdParam.vcutof) packAndSend(fid.vfloat, scdParam.vfloat) packAndSend(fid.vrecharge, scdParam.vrecharge) packAndSend(fid.uvstart, scdParam.uvstart) packAndSend(fid.uvoff, scdParam.uvoff) packAndSend(fid.uvon, scdParam.uvon) packAndSend(fid.overtemp, scdParam.overtemp, 10) packAndSend(fid.lowtemp, scdParam.lowtemp, 10) packAndSend(fid.unovert, scdParam.unovert, 10) packAndSend(fid.unlowt, scdParam.unlowt, 10) end --- 上传预警信息 -- t:type -- s:status function upwarn(t,s) log.warn("------------------------t,:",t) log.warn("------------------------s,:",s) local dat -- 设备上报数据表 local data = { type = t, status = s, } message.cmd = "warn" message.ext = data dat = json.encode(message) log.info("upload warn:", dat) return dat end ------------------------------------------------------------------------------------------------------ --- 打印数据信息 function PrintData() sys.wait(1000) if result.ds == 4 then result.ds = 1 end --滤除设备开关机状态标志位异常 log.warn("++++++++++++++++++++++++++++++++++++++++Parameter display start!!+++++++++++++++++++++++++++++++++++++++++++++++") print("Table:", result) print( "eeprom state:", result.iSave, "\nDevice Status:", result.ds, "\nLignt control times:", result.tt, "\nWork Status:", result.ws, "\nLignt control Status:", result.lps, "\nRain control Status:", result.rps, "\ntempture control Status:", result.tps, "\nDump Protect:", result.dps, "\nvoltage Status:", result.vps, "\nCharging voltage:", result.cv, "\nBattery voltage:", result.bv, "\nBoard temperature:", result.bt, "\nLight control Type:", paramconf.lcm, "\nSunup voltage:", paramconf.vsunrise, "\nSunset voltage:", paramconf.vsunset, "\nCharging up to voltage:", paramconf.vcutof, "\nfloating charge voltage:", paramconf.vfloat, "\nonce again startup charging action voltage:", paramconf.vrecharge, "\nfirst startup voltage:", paramconf.vstart, "\nundervoltage clear voltage:", paramconf.uvoff, "\nundervoltage lock voltage:", paramconf.uvon, "\nHigh temperature Protect:", paramconf.overtemp, "\nLow temperature Protect:", paramconf.lowtemp, "\nHigh temperature clear:", paramconf.unovert, "\nLow temperature clear:", paramconf.unlowt, "红外计数器:", infrared_count, "\nVol counts:", result.kcnt, "\nboard version:", result.ver) log.warn("++++++++++++++++++++++++++++++++++++++++Parameter display end!!+++++++++++++++++++++++++++++++++++++++++++++++") end --+++++++++++++++++++++++++++++++++++++++++获取主板信息+++++++++++++++++++++++++++++++++++++++++ -- 获取主板状态 -->STM8从机地址0x51 local function getStatus() local data = string.char(0x55,0x03) uart.write(1,data) sys.wait(300) end -------------------------------------------------------------------------------------------------------------- -- ====================================================上传=================================================== ------------------------------------------------- 上传数据信息-四情平台 ---------------------------------------- function upData_120(...) local data, c, dat = {} getStatus() -- 获取主板状态 data.imei = misc.getImei() -- 唯一ID data.iccid = string.upper(sim.getIccid()) --获取SIM卡的iccid号 ++++ 注意:开机lua脚本运行之后,会发送at命令去查询iccid,所以需要一定时间才能获取到iccid。开机后立即调用此接口,基本上返回nil data.csq = net.getRssi() -- 信号强度 data.dver = VERSION -- 版本号 (main.lua第二行) data.proj = PROJECT -- 设备名称 (main.lua第一行) data.stm8vs = string.format(result.ver) -- 主板版本号 ------------------------------------------- data.ds = result.ds or 1 -- 设备是否开机 data.ws = result.ws or 1 -- 工作状态 0待机 1工作 data.cs = result.lps or 0 -- 充电标志位 0 非充电,1 充电 data.rps = result.rps or 0 -- 雨控 data.tps = result.tps or 0 -- 温控 data.dps = result.dps or 0 -- 倾倒 data.bs = result.vps or 0 -- 正常0 欠压 1 过压 2 -------------------------------------- data.tcs = timcontrl.timctrl --时控开关 data.st = timcontrl.st --时控开始时间 data.et = timcontrl.et --时控结束时间 -------------------------------------- data.lcm = result.lcm or 0 -- 光控类型 0太阳能板光控 1光敏二极管光控 data.cv = result.cv or 0 -- 充电电压 单位:mV data.bv = result.bv or 12000 -- 电池电压 单位:mV data.bt = result.bt / 10 -- 主板温度 data.at = result.bt/10 --环境温度 data.ah = hum or 30.0 -- 环境湿度 data.infr_ct = infrared_count -- 红外计数 if data.infr_ct > 70 then --过滤掉开机之后的红外计数异常 data.infr_ct = 0 end data.volt_ct = result.kcnt -- 高压计数值 if data.volt_ct > 10 then --过滤掉开机之后的电击计数异常 data.volt_ct = 0 end data.wind_drec = 666 data.wind_sped = 66.6 ----------------------------------------- rebootcnt = io.readFile(DEV_REBOOT) data.bt_ct = rebootcnt -- 设备重启次数 log.warn("Device Reboot times is:", rebootcnt) data.gps = gps_status -- 定位标志位 0 手动定位,1 GPS定位,2 LBS定位 if gps_status == 0 then data.lat = manual_location.lat data.lng = manual_location.lng elseif gps_status == 1 then data.lat = gps_loc_lat data.lng = gps_loc_lng elseif gps_status == 2 then data.lat = lbs_loc_lat data.lng = lbs_loc_lng end log.warn("upload LBS data message:", data.lat, data.lng) c = misc.getClock() -- 获取系统时间 data.stamp = string.format("%04d%02d%02d%02d%02d%02d", c.year, c.month, c.day, c.hour, c.min, c.sec) message.cmd = "data" message.ext = data dat = json.encode(message) log.info("upload data:", dat) --ClearKcnt() --上报数据清零红外 return dat end ------------------------- 上传参数配置信息 function upStatus() local status, dat = {} getStatus()-- 获取主板状态 status.imei = misc.getImei() -- 唯一ID status.iccid = string.upper(sim.getIccid())--获取SIM卡的iccid号 ++++ 注意:开机lua脚本运行之后,会发送at命令去查询iccid,所以需要一定时间才能获取到iccid。开机后立即调用此接口,基本上返回nil status.csq = net.getRssi() -- 信号强度 status.tt = result.tt or 0 -- 定时时长 message.cmd = "status" message.ext = status dat = json.encode(message) log.info("upload status:", dat) return dat end ----------------------------------------------------------------------------------------------------------------- --------------------------------------- 上传数据信息-------大数据平台---------------------------------------------- function upData() local data, c, dat = {} getStatus() -- 获取主板状态 data.imei = misc.getImei() -- 唯一ID data.iccid = string.format(sim.getIccid()) -- 获取SIM卡的iccid号 data.csq = string.format(net.getRssi()) -- 信号强度 data.dver = VERSION -- 版本号 (main.lua第二行) data.proj = PROJECT -- 设备名称 (main.lua第一行) data.stm8vs = string.format(result.ver) -- data.dtype = "4" -- 设备类型 -性诱III data.btype = "0" -- 0 蓄电池,1锂电池 data.ds = string.format(result.ds or 1) -- 设备是否开机 data.ws = string.format(result.ws or 1) -- 工作状态0待机,1工作,2充电 data.cs = string.format(result.lps or 0) -- 充电标志位 0 非充电,1 充电 data.rps = string.format(result.rps or 0) -- 雨控 data.tps = string.format(result.tps or 0) -- 温控 data.dps = string.format(result.dps or 0) -- 倾倒 data.bs = string.format(result.vps or 0) -- 正常0 欠压 1 过压 2 data.lcm = string.format(result.lcm or 0) -- 光控类型 0太阳能板光控 1光敏二极管光控 data.bt = string.format(result.bt / 10) -- 主板温度 data.ts = string.format(timcontrl.timctrl) -- 时控开关 data.st = string.format(timcontrl.st) -- 时控开始时间 data.et = string.format(timcontrl.et) -- 时控结束时间 data.cv = string.format((result.cv or 18000) / 1000) -- 充电电压 data.bv = string.format((result.bv or 12800) / 1000) -- 电池电压 data.at = string.format(result.bt/10) or "25.0" -- 环境温度 data.ah = string.format(hum) or "30.0" -- 环境湿度 data.volt_ct = string.format(result.kcnt) -- 电击次数 if tonumber(data.volt_ct) > 10 then --过滤掉开机之后的电击计数异常 data.volt_ct = "0" end data.infr_ct = infrared_count -- 光电开关计数值 if tonumber(data.infr_ct) > 70 then -- 过滤掉开机之后的光栅计数异常 data.infr_ct = 0 end data.wind_drec = "666" data.wind_sped = "66.6" data.dat_f = string.format(dat_f) -- 数据上传时间间隔 data.clt_t = string.format(clt_t) -- 清虫时间间隔 rebootcnt = io.readFile(DEV_REBOOT) if rebootcnt == nil or rebootcnt == "" then log.info("first startup!!!!!!!!") rebootcnt = 0 rebootcnt = tonumber(rebootcnt) end log.warn("Device Reboot times is:", rebootcnt) data.rcnt = string.format(rebootcnt) -- 重启次数 data.gps = string.format(gps_status) -- 定位标志位 0 手动定位,1 GPS定位,2 LBS定位 if gps_status == 0 then data.lat = manual_location.lat data.lng = manual_location.lng elseif gps_status == 1 then data.lat = gps_loc_lat data.lng = gps_loc_lng elseif gps_status == 2 then data.lat = lbs_loc_lat data.lng = lbs_loc_lng end c = misc.getClock() data.stamp = string.format("%04d%02d%02d%02d%02d%02d", c.year, c.month, c.day, c.hour, c.min, c.sec) message.cmd = "data" message.ext = data dat = json.encode(message) log.info("upload data:", dat) --ClearKcnt(); --清除点击次数 return dat end ----------------------------------------------------------------------------------------------------------- ----------------------------------------- 物联网模块参数配置开始 -------------------------------------------- ----------------------------------------- 上传主板参数配置信息----------------------------------------------- function upParamConf(...) local c, dat paramconf.imei = misc.getImei() -- 唯一ID c = misc.getClock() paramconf.stamp = string.format("%04d%02d%02d%02d%02d%02d", c.year, c.month, c.day, c.hour, c.min, c.sec) message.cmd = "paramconf" message.ext = paramconf dat = json.encode(message) log.info("upload paramconf:", dat) return dat end ----------------------------------------- 上传主服务器配置信息-------------------------------------------------- function upServerConf(...) local dat serverconf.imei = misc.getImei()-- 唯一ID message.cmd = "serverconf" message.ext = serverconf dat = json.encode(message) log.info("upload serverconf:", dat) return dat end ----------------------------------------- 上传第三方服务器配置信息--------------------------------------------- function upThirdserverConf(...) local dat thirdserverconf.imei = misc.getImei()-- 唯一ID message.cmd = "thirdserverconf" message.ext = thirdserverconf dat = json.encode(message) log.info("upload thirdserverconf:", dat) return dat end -- 设备给客户端的反馈 -->远程控制设备更新和重启等 function upres(c_type, c_status) local dat -- 设备上报数据表 local data = { type = c_type, status = c_status } message.cmd = "warn" message.ext = data dat = json.encode(message) log.info("upload upres:", dat) return dat end ------------------------------------------------- 物联网模块参数配置结束 -------------------------------------------------------- ------------------------------------------------------------------------------------------------------------------------------ --++++++++++++++++++++++++++++++++++++++++++++++++ 功能函数集合 开始++++++++++++++++++++++++++++++++++++++++++++++++++++++++ ---------------------------------------------------主板参数下发配置 开始-------------------------------------------------------- --- 设置主板开关机 function setsw(pwb) local setsw_cnt = 0 local set_onoff = string.char(0xAA,0x01,pwb) while result.ds ~= pwd do setsw_cnt = setsw_cnt + 1 uart.write(1,set_onoff) if setsw_cnt == 2 then break end sys.wait(500) end log.info("设备开关机:", pwb) end --- 设置主板光控定时时长 -- @param tt, number类型 function setTimer(tt) if not tt then return end if (tt <= 0 or tt > 8) and tt ==nil and tt == "" then log.error("setTimer value error!!!!!!!") return end local send_cnt = 0 local dat_freq = string.char(0xAA,0x02,tt) while tt~=result.tt do send_cnt = send_cnt + 1 uart.write(1,dat_freq) if send_cnt == 3 then break end end log.info("定时模式为光控,时长:", tt) end ---清零红外和高压计数值 function ClearKcnt() local kcnt = 0 local clear = string.char(0xAA,0x06) while true do kcnt = kcnt +1 if result.infr_ct ~=0 or result.volt_ct ~=0 then uart.write(1,clear) end if kcnt == 2 then break end sys.wait(500) end log.info("clear kcnt!!!!") end ---清虫 local function Clearworm() local setsw_cnt = 0 local clear_worm = string.char(0xAA,0x05) while true do setsw_cnt = setsw_cnt + 1 uart.write(1,clear_worm) sys.wait(500) if setsw_cnt == 2 then break end --确保置位清虫标志位 end log.info("clear worm!!!!") end --下发时控设置 function SetTimControl(crtl,st1,et1) if crtl == nil or crtl == "" then return end if st1==nil or st1=="" or et1 ==nil or et1 == "" then return end st = tonumber(st1) et = tonumber(et1) if (st < 1 or st > 23) or (et < 1 or et > 23) then log.error("value error!!!!!!!!!!") return end if crtl == 1 or crtl == 0 then timcontrl.timctrl = crtl end if (st >= 0 and st <=23) and ( et >= 0 and et <= 23) then timcontrl.st = st timcontrl.et = et end log.info("时控参数:", "timctrl:", timcontrl.timctrl, "st:", timcontrl.st, "et:", timcontrl.et) local data = json.encode(timcontrl) io.writeFile(CONTROL_CONF, data) end --- 设置清虫时间间隔 function SetCleartime(clt) if not clt then return end if clt < 1 or clt > 120 then log.error("clt value error******") return end if clt > 9 and clt < 121 then cleartim = clt end log.info("设置清虫时间间隔为:", cleartim, "分钟") io.writeFile(CLEART_CONF, cleartim) end --- 下发配置数据上传时间间隔: function setDattim(dat) if not dat then return end if dat < 1 or dat > 120 then log.error("Dattim value error!!!!!!!") return end if dat > 9 and dat < 121 then dattim = dat end log.info("设置数据上传时间间隔为:", dattim, "分钟") io.writeFile(DATTIM_CONF, dattim) end -- 一键测试函数 function Test_key() if stm8_update_sw == 1 then return end local test = string.char(0XAA,0X0A) uart.write(1,test) end --下发主板升级命令 function update_stm32() local update_cnt = 0 local up_date_32 = string.char(0xAA,0xA0) while true do update_cnt = update_cnt + 1 uart.write(1,up_date_32) sys.wait(500) if update_cnt == 2 then break end end log.info("update_stm32 begin!!!!") end --光控模式切换 function Light_control_handoff() local Light_control1 = string.char(0xAA,0x03,0x01) local Light_control2 = string.char(0xAA,0x03,0x00) while true do if result.lcm == 0 then uart.write(1,Light_control1) elseif result.lcm == 1 then uart.write(1,Light_control2) end return end log.info("Light control handoff begin!!!!") end --下发BootLoader交互命令 function BootLoader_stm32() local boot_count = 0 local BootLoader_32 = string.char(0x31) while true do boot_count = boot_count + 1 uart.write(1,BootLoader_32) sys.wait(200) if boot_count == 2 then break end end log.info("BootLoader begin!!!!") end ----------------------------------------------------------------------------------------------------------------------------- --================================================ 主板参数下发配置 结束 ======================================================= -----------------------------------------------反向获取平台温湿度接口传回MQTT 开始---------------------------------------------------- function Setsensor_value(dat_sensor) local cmds,result,err = json.decode(dat_sensor) if not result then return end if cmds.ext.new_hum~=nil and cmds.ext.new_hum~="" then if tonumber(cmds.ext.new_hum)~= nil and tonumber(cmds.ext.new_hum)>=0 and tonumber(cmds.ext.new_hum)<= 100 then hum = tonumber(cmds.ext.new_hum) if nvm.get("hum")~= hum then nvm.set("hum",hum) end end end if cmds.ext.new_tem~=nil and cmds.ext.new_tem~="" then if tonumber(cmds.ext.new_tem)~= nil and tonumber(cmds.ext.new_tem) < 100 then temp = tonumber(cmds.ext.new_tem) if nvm.get("temp")~= temp then nvm.set("temp",temp) end end end log.warn(">>>>>>>>>sensor data get is:>>>>>>>>>>",hum,temp) end -----------------------------------------------反向获取平台温湿度接口传回MQTT 结束---------------------------------------------------- --------------------------------------------------------------------------------------------------------------------------- ------------------------------------------------- 物联网模块参数配置开始 ------------------------------------------------------ ---------------------------------------------------下发用户配置的参数---------------------------------------------------------- -- --- 下发配置数据上传时间间隔 -- @param dat, json数据结构 function Set_dattim(dat) if nvm.get("platform")== "120.27.222.26" then local cmds, result, err = json.decode(dat) if not result then log.info("Set_dattim set the parameter error!") end if type(cmds.ext.dat_f) == "number" and cmds.ext.dat_f >= 10 and cmds.ext.dat_f <= 120 then -- number类型 data dat_f = cmds.ext.dat_f else log.error("EEEE:::::::::::::Dattim parameter not number or not range:::::::::::::::EEEE") return end log.warn("Set_dattim set the parameter value is: ", dat_f, "minutes") io.writeFile(DATTIM_CONF, dat) else local cmds, result, err = json.decode(dat) if not result then log.info("Set_dattim set the parameter error!") end dat_f = tonumber(cmds.ext.data_tim.dat_f) log.warn("Set_dattim set the parameter value is: ", dat_f, "minutes") paramtable.ext.data_tim.dat_f = dat_f local dat = json.encode(paramtable) -- 参数配置存入文件 io.writeFile(PRARM_CONF,dat) end end -- --- 下发配置清虫时间间隔 -- @param dat, json数据结构 function Set_clttim(dat) local cmds, result, err = json.decode(dat) if not result then log.info("Set_dattim set the parameter error!") end clt_t = tonumber(cmds.ext.clt_tim.clt_t) log.warn("Set_dattim set the parameter value is: ", clt_t, "minutes") paramtable.ext.clt_tim.clt_t = clt_t local dat = json.encode(paramtable) -- 参数配置存入文件 io.writeFile(PRARM_CONF,dat) end --- 下发设置时控参数 -- @param dat, json数据结构 function Set_timcontrol(dat) --四情平台设置 if nvm.get("platform")== "120.27.222.26" then local cmds, result, err = json.decode(dat) if not result then log.error("Set_timcontrol error!!!!!") end timcontrl = cmds.ext log.warn("Set_timcontrol set the parameter value is: ", timcontrl) io.writeFile(CONTROL_CONF, dat) else --大数据平台设置 local cmds, result, err = json.decode(dat) if not result then log.error("Set_timcontrol error!!!!!") end if cmds.ext.work_tim.timctrl ~= nil and type(cmds.ext.work_tim.timctrl) == "string" and tonumber(cmds.ext.work_tim.timctrl) >= 0 and tonumber(cmds.ext.work_tim.timctrl) <= 1 then timcontrl.timctrl = tonumber(cmds.ext.work_tim.timctrl) end if cmds.ext.work_tim.st ~= nil and type(cmds.ext.work_tim.st) == "string" and tonumber(cmds.ext.work_tim.st) >= 0 and tonumber(cmds.ext.work_tim.st) <= 23 then timcontrl.st = tonumber(cmds.ext.work_tim.st) end if cmds.ext.work_tim.et ~= nil and type(cmds.ext.work_tim.et) == "string" and tonumber(cmds.ext.work_tim.et) >= 0 and tonumber(cmds.ext.work_tim.et) <= 23 then timcontrl.et = tonumber(cmds.ext.work_tim.et) end log.warn("Set_timcontrol set the parameter value is: ", timcontrl) paramtable.ext.work_tim = timcontrl local dat = json.encode(paramtable) -- 参数配置存入文件 io.writeFile(PRARM_CONF,dat) end end --- 下发参数配置信息 -- @param dat, json数据结构 function setParamConf(dat) local cmds, result, err = json.decode(dat) if not result then log.info("setParamConf set the parameter error!") end scdParam = cmds.ext log.warn("setParamConf set the parameter value is: ", paramconf) io.writeFile(DEVICE_CONF, dat) SetStatus() end --- 下发服务器配置信息 -- @param dat, json数据结构 function setServerConf(dat) local cmds, result, err = json.decode(dat) if not result then log.info("setServerConf set the parameter error!") end serverconf = cmds.ext log.warn("setServerConf set the parameter value is: ", serverconf) io.writeFile(SERVER_CONF, dat) end --- 下发第三方服务器配置信息 -- @param dat, json数据结构 function setThirdserverConf(dat) local cmds, result, err = json.decode(dat) if not result then log.info("setThirdserverConf set the parameter error!") end thirdserverconf = cmds.ext log.warn("setThirdserverConf set the parameter value is: ", thirdserverconf) io.writeFile(THIRD_CONF, dat) end --- 下发设置定位数据(--百度坐标系--) -- @param dat, json数据结构 function Set_location(dat) local cmds, result, err = json.decode(dat) if not result then log.warn("Set work location failed!") end manual_location = cmds.ext log.warn("set manual_location is:",manual_location.lat,manual_location.lng) --paramtable.ext.location = manual_location --local dat = json.encode(paramtable) -- 参数配置存入文件 io.writeFile(GPS_CONF,dat) end ----------------------------------------------------------------------------------------------------------------------------- ---------------------------------------------------读取用户配置的参数---------------------------------------------------------- --- 开机获取用户配置的参数 function getConfig() local param, server,datt, third_ser,loc,param_conf, cmds, result, err param = io.readFile(DEVICE_CONF) -- 获取参数配置参数 cmds, result, err = json.decode(param) if result then paramconf = cmds.ext end datt = io.readFile(DATTIM_CONF) -- 获取数据上传时间间隔参数 cmds, result, err = json.decode(datt) if result then dat_f = cmds.ext.dat_f end server = io.readFile(SERVER_CONF) -- 开机读取主服务器配置 cmds, result, err = json.decode(server) if result then serverconf = cmds.ext end third_ser = io.readFile(THIRD_CONF) -- 获取第三方服务器配置参数 cmds, result, err = json.decode(third_ser) if result then thirdserverconf = cmds.ext end loc = io.readFile(GPS_CONF) -- 开机读取手动定位值 cmds,result,err = json.decode(loc) if result then manual_location = cmds.ext end ----------------------------设备参数读取失败重置默认参数------------------------------------ param_conf = io.readFile(PRARM_CONF) cmds, result, err = json.decode(param_conf) if result then dat_f = cmds.ext.data_tim.dat_f -- 获取数据上传时间间隔参数 clt_t = cmds.ext.clt_tim.clt_t -- 获取清虫间隔参数 timcontrl = cmds.ext.work_tim -- 获取时控控制参数 if timcontrl == nil then timcontrl.st = 20 timcontrl.et = 0 timcontrl.timctrl = 0 end -- manual_location = cmds.ext.location -- 获取手动定位值 end end ----------------------------------------------------------------------------------------------------------------------------- ------------------------------------------------- 物联网模块参数配置结束 ------------------------------------------------------ -- +++++++++++++++++++++++++++++++++++++++++++++++++ 协程功能进程开始 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -------------------------------------------------------定时清虫任务------------------------------------------------------------ --+++++性诱测报III型设备没有定时清虫功能----可以屏蔽该段代码 sys.taskInit(function() while true do sys.wait(clt_t * 60 *1000) --30分钟清虫一次 Clearworm() log.warn("Clear worm time is:", clt_t) end end) -----------------------------------------------定时工作任务---------------------------------------------------- -- 定时模式启动判断 sys.taskInit( function() worksta = 0 local workdone = 0 --(光控定时模式下)工作完成标志位 local timeover = 0 --定时模式结束时间戳 sys.wait(30 * 1000) --等待开机启动对时 log.warn("Read timctrl is..................", timcontrl.timctrl) local c = misc.getClock() while true do while true do if c.year < 2020 then --如果未对时,关闭时控 timcontrl.timctrl = 0 c = misc.getClock() end if timcontrl.timctrl == 0 then -- 若时控关闭 log.warn("it's not time control") log.warn("开始时间:", timcontrl.st, "结束时间:", timcontrl.et) worksta = 0 workdone = 0 end if timcontrl.timctrl == 1 then -- 若时控开启 log.warn("it's time control", "start time:", timcontrl.st, "end time:", timcontrl.et) local c_sta = misc.getClock() c_sta.hour = timcontrl.st c_sta.min = 0 c_sta.sec = 0 if timcontrl.st < timcontrl.et then -- 如果开始和结束时间是同一天 log.warn("the same day !!!!") local c_end = misc.getClock() -- **获取当前时间** c_end.hour = timcontrl.et c_end.min = 0 c_end.sec = 0 -- 如果当前时间大于开始时间且小于结束时间,且没有开始工作 if os.difftime(os.time(), os.time(c_sta)) > 0 and os.difftime(os.time(), os.time(c_end)) < 0 and workdone == 0 then log.warn("模式1当前时间大于开始时间,且没有开始工作,当前时间小于结束时间的情况:计算结束时间戳") timeover = os.time(c_end) timeover = tonumber(timeover) worksta = 1 break elseif os.difftime(os.time(), os.time(c_sta)) < 0 then log.warn("模式1当前时间小于开始时间!!!") worksta = 0 elseif os.difftime(os.time(), os.time(c_end)) > 0 then log.warn("模式1当前时间大于结束时间!!!") worksta = 0 end -- 如果工作完成: if workdone == 1 then workdone = 0 end elseif timcontrl.st > timcontrl.et then -- 如果结束时间是第二天 log.warn("not the same day !!!!") local n = misc.getClock() -- **获取当前时间** -- 如果当前时间大于开始时间,且没有开始工作 ,注意时间戳日期加1 if os.difftime(os.time(), os.time(c_sta)) > 0 and workdone == 0 and n.hour > timcontrl.et then log.warn("模式2当前时间大于开始时间,且没有开始工作,当前时间位于0点之前,结束时间戳加1天,计算结束时间戳") local c_end = misc.getClock() c_end.hour = timcontrl.et c_end.min = 0 c_end.sec = 0 timeover = os.time(c_end) + 3600 * 24 timeover = tonumber(timeover) worksta = 1 break elseif os.difftime(os.time(), os.time(c_sta)) > 0 and workdone == 0 and n.hour < timcontrl.et then log.warn("模式2当前时间大于开始时间,但是小于结束时间,当前时间位于0点之后,所以是重启引起的,时间戳不动,计算结束时间戳") local c_end = misc.getClock() c_end.hour = timcontrl.et c_end.min = 0 c_end.sec = 0 timeover = os.time(c_end) worksta = 1 break elseif os.difftime(os.time(), os.time(c_sta)) < 0 then log.warn("模式2当前时间小于开始时间!!!") worksta = 0 end -- 如果工作完成: if workdone == 1 then workdone = 0 end end end sys.wait(1000) end -- 等待定时任务完成 if timeover ~= nil or timeover ~= 0 then while (timeover > os.time()) do sys.wait(1000) log.warn("Working.....:", "over", timeover, "now:", os.time()) end end log.info(" The workTask time is end!") ----------------------标志工作定时结束!!!++++ worksta = 0 workdone = 1 ----------------------标志工作完成!!!++++ sys.wait(1000) end end ) -- 时控判断是否工作------------------------------------------------- sys.taskInit( function() sys.wait(20 * 1000) while true do if timcontrl.timctrl == 1 then --时控定时模式 log.warn("Start Timng Mode....") if worksta == 1 then if result.ds == 0 then -- 如果设备关机 setsw(1) --开机 end else if result.ds == 1 then -- 如果设备开机 setsw(0) end end end if timcontrl.timctrl == 0 then --光控 log.warn("Light control mode...") end if timcontrl.timctrl ~= timcontrl.timctrl then --如果时控状态改变清除当前计数值 infrared_count = 0 end sys.wait(1000) end end ) --时控工作修改光控工作状态消除时控工作状态下不能达到工作时长 sys.taskInit( function () local cnf, result, err = json.decode(dat) sys.wait(1000) while true do if timcontrl.timctrl == 1 then tt = 0 setTimer(0) end sys.wait(1000) end end ) -----------------------------------------------雨控即时上报---------------------------------------------------- --雨控即时上报 sys.taskInit( function() sys.wait(1000) while true do if rps_x == 1 then updata_freq = 0 rps_x = 0 rps_y = 1 end sys.wait(1000) end end ) ------------------------------------------------------------协程通讯进程开始---------------------------------------------------------- -- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ MQTT1 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ sys.taskInit(function() getConfig() -- 开机获取用户配置的参数 nvm.init("config.lua") sys.wait(5000) log.info("MQTT1 Task is start!") -- 是否获取分配到的ip while not socket.isReady() do log.info("socket is not ready,err_num:", err_num) err_num = err_num + 1 sys.wait(1000) if err_num >= 600 then rebootinfo = 2 -- ***SOCKET断开上报***(注意只针对120.27.222.26服务器) io.writeFile(DEVICE_ERR, rebootinfo) sys.restart("socket connect overtime!") end end serverconf.ip = nvm.get("platform") if serverconf.ip == "8.136.98.49" then serverconf.port = 61883 sub = "/yfkj/xycb/s2c/" -- 服务器到客户端 pub = "/yfkj/xycb/c2s/" -- 客户端到服务器 lastwill = "/yfkj/xycb/offline/" -- 离线消息主题(部分)-->设备异常中断时用于mqtt服务器发布该设备的遗愿消息,个人网站客户端需订阅 elseif serverconf.ip == "120.27.222.26" then serverconf.port = 1883 sub1 = "yfkj/xycb/s2c/" -- 服务器到客户端 pub1 = "yfkj/xycb/c2s/" -- 客户端到服务器 lastwill1 = "yfkj/xycb/offline/" -- 离线消息主题(部分)-->设备异常中断时用于mqtt服务器发布该设备的遗愿消息,个人网站客户端需订阅 end if nvm.get("lat_lbs") ~= "" and nvm.get("lat_lbs") ~= nil then lbs_loc_lat = nvm.get("lat_lbs") lbs_loc_lng = nvm.get("lng_lbs") gps_status = 2 end if nvm.get("lat_gps") ~= "" and nvm.get("lat_gps") ~= nil then gps_loc_lat = nvm.get("lat_gps") gps_loc_lng = nvm.get("lng_gps") gps_status = 1 end if nvm.get("hum") ~= "" and nvm.get("hum") ~= nil then hum = nvm.get("hum") end if nvm.get("temp") ~= "" and nvm.get("temp") ~= nil then temp = nvm.get("temp") end -- 离线消息 willmsg.ext.imei = misc.getImei() if serverconf.ip == "8.136.98.49" then serverconf.lastwill = "/yfkj/xycb/offline/" serverconf.pub = "/yfkj/xycb/c2s/" serverconf.sub = "/yfkj/xycb/s2c/" elseif serverconf.ip == "120.27.222.26" then serverconf.lastwill = "yfkj/xycb/offline/" serverconf.pub = "yfkj/xycb/c2s/" serverconf.sub = "yfkj/xycb/s2c/" end local will = {qos = 1, retain = 0, topic = string.format(serverconf.lastwill .. misc.getImei()), payload = json.encode(willmsg)} -- 创建mqtt客户端--默认配置了MQTT遗愿消息 local mqttc = mqtt.client(misc.getImei(), serverconf.keepalive, serverconf.uid, serverconf.pwd, 1,will) local pub = string.format(serverconf.pub .. misc.getImei()) local sub = string.format(serverconf.sub .. misc.getImei()) local mqtt_sta = true while true do -- 连接mqtt服务器 mqtt_sta = mqttc:connect(serverconf.ip, serverconf.port) log.info('mqtt connect status::', mqtt_sta) if mqtt_sta == false then log.info("mqtt1 connect fail,try to reconnect!", tcp_cont) tcp_cont = tcp_cont + 1 if tcp_cont >= 600 then rebootinfo = 3 -- ***MQTT断开上报*** io.writeFile(DEVICE_ERR, rebootinfo) sys.restart("mqtt1 reconnect overtime:60!!!") end end -- 订阅主题 if mqttc:subscribe(sub, serverconf.qos) then local reason = rtos.poweron_reason() log.info("reason:", reason) mqttc:publish(pub,upwarn("device_820UG","turnon:" ..rtos.poweron_reason() ..";stm32:"..nvm.get("reboot_stm8")..";freefilesize:" ..rtos.get_fs_free_size() .. ";VERSION:" .. VERSION .. ";"..PROJECT.. "&core_version:" .. rtos.get_version() ..";stm8:"..result.ver),serverconf.qos) if serverconf.ip == "8.136.98.49" then if not mqttc:publish(pub, upData(), serverconf.qos) then break end elseif serverconf.ip == "120.27.222.26" then if not mqttc:publish(pub, upStatus(), serverconf.qos) then break end if not mqttc:publish(pub, upData_120(), serverconf.qos) then break end end log.info("MQTT1 upload is done!") while mqtt_sta==true do mqtt_status = "true" --local r, packet = mqttc:receive(dattim * 60 * 1000) -- 处理服务器下发指令 local r, packet, param = mqttc:receive(timeout * 1000 * 60, "NET_SENT_RDY_") if r then -- 这里是有数据下发的处理 datalink = 2 local cnf, result, err = json.decode(packet.payload) if result then log.info("MQTT1 recv json is::::::::::::::::::::::::::::::::::::::::::::::", packet.payload) if serverconf.ip == "8.136.98.49" then -----------------------------------设备参数读取-------------------------------- if cnf.cmd == "read" then if cnf.ext == 'data' then --参数读取 updata_freq = 0 elseif cnf.ext == 'paramconf' then --获取参数配置 if not mqttc:publish(pub, upParamConf(), serverconf.qos) then break end elseif cnf.ext == 'serverconf' then --获取主服务器参数配置 if not mqttc:publish(pub, upServerConf(), serverconf.qos) then break end updata_freq = 0 elseif cnf.ext == 'thirdserver_conf' then --获取第三方服务器配置 if not mqttc:publish(pub, upThirdserverConf(), serverconf.qos) then break end updata_freq = 0 end --------------------------------平台设备控制参数下发----------------------------------- elseif cnf.cmd == 'paramconf' then if cnf.ext.data_tim ~= nil then -- 大数据平台配置数据上传时间间隔 Set_dattim(packet.payload) sys.wait(300) end if cnf.ext.clt_tim ~= nil then -- 大数据平台配置清虫时间间隔 Set_clttim(packet.payload) sys.wait(300) end if cnf.ext.work_tim ~= nil then -- 大数据平台配置定时控制参数 Set_timcontrol(packet.payload) sys.wait(300) end if cnf.ext.power ~= nil then -- 大数据平台开关机控制 setsw(tonumber(cnf.ext.power.ds)) sys.wait(300) end if cnf.ext.location ~= nil then -- 大数据平台下发手动定位 Set_location(packet.payload) sys.wait(300) end if not mqttc:publish(pub, upres("SCD-paramconf","data_tim is".." "..cnf.ext.data_tim.dat_f.." ".."clt_tim is".." "..cnf.ext.clt_tim.clt_t.." ".."TimControl".." "..cnf.ext.work_tim.timctrl.." ".."start_time".." "..cnf.ext.work_tim.st.." ".."end_time".." "..cnf.ext.work_tim.et.." ".."power is".." "..cnf.ext.power.ds), serverconf.qos) then break end --------------------------------------------------------------------------------------------------------- elseif cnf.cmd == "clearworm" then -- 大数据平台清虫 if not mqttc:publish(pub, upres("xy-clrworm", "Remote clearworm action will run!!"), serverconf.qos) then break end sys.publish("clearworm") Clearworm() updata_freq = 0 sys.wait(300) elseif cnf.cmd == "reboot" then -- 大数据平台重启 if not mqttc:publish(pub, upres("air820-reboot", "System will restart!!"), serverconf.qos) then break end sys.restart("Device remote restart") elseif cnf.cmd == "update" then -- 大数据平台物联网模块升级 if not mqttc:publish(pub, upres("air820-updata", "System will update!!"), serverconf.qos) then break end Update.run() elseif cnf.cmd == "update_stm32" then -- 大数据平台主板stm32升级 if not mqttc:publish(pub, upres("update_stm32", "stm32 update will start!!"), serverconf.qos) then break end stm8_update_sw = 1 update_stm32() --STM32远程升级 ----------------------------参数配置下发------------------------------ elseif cnf.cmd == 'param_conf' then -- 大数据平台设备参数配置下发 setParamConf(packet.payload) updata_freq = 0 elseif cnf.cmd == 'server_conf' then -- 大数据平台服务器配置下发 setServerConf(packet.payload) updata_freq = 0 sys.restart("server_conf done then restart!!!") elseif cnf.cmd == 'thirdserver_conf' then -- 大数据平台第三方服务器配置下发 setThirdserverConf(packet.payload) sys.restart("thirdserver_conf done then restart!!!") elseif result and cnf.cmd=="platform" then----平台切换参数下发 if cnf.ext.type == "120.27.222.26" then nvm.set("platform","120.27.222.26") sys.restart("120.27.222.26") elseif cnf.ext.type == "8.136.98.49" then nvm.set("platform","8.136.98.49") sys.restart("8.136.98.49") end local c = misc.getClock() local date = string.format("%00004d-%02d-%02d %02d:%02d:%02d", c.year, c.month, c.day, c.hour, c.min, c.sec) if not mqttc:publish(pub,upwarn("平台操作","切换平台至:"..cnf.ext.type..",操作时间:"..date), serverconf.qos) then break end end elseif serverconf.ip == "120.27.222.26" then if cnf.cmd == "read" then if cnf.ext == 'status' then --状态读取 updata_freq = 0 elseif cnf.ext == 'data' then --参数读取 updata_freq = 0 elseif cnf.ext == 'paramconf' then --获取参数配置 if not mqttc:publish(pub, upParamConf(), serverconf.qos) then break end elseif cnf.ext == 'serverconf' then --获取主服务器配置 if not mqttc:publish(pub, upServerConf(), serverconf.qos) then break end elseif cnf.ext == 'thirdserver_conf' then --第三方服务器配置读取 if not mqttc:publish(pub, upThirdserverConf(), serverconf.qos) then break end updata_freq = 0 end elseif cnf.cmd == 'set' then if cnf.ext.type == "data_tim" then -- 四情平台配置数据上传时间间隔 Set_dattim(packet.payload) updata_freq = 0 sys.wait(300) elseif cnf.ext.type == "work_tim" then -- 四情平台配置定时控制参数 Set_timcontrol(packet.payload) updata_freq = 0 sys.wait(300) else log.error("EEEE:::::::::::::not set match:::::::::::::::EEEE") end elseif cnf.cmd == "ctrl" then if cnf.ext.type == "power" then -- 四情平台开关机 if not mqttc:publish(pub, upres("Remote startup&shutdown action will run!", "ok"), serverconf.qos) then break end setsw(cnf.ext.ds) updata_freq = 0 sys.wait(300) elseif cnf.ext == "clearworm" then -- 四情平台清虫 if not mqttc:publish(pub, upres("Remote clearworm action will run!", "ok"), serverconf.qos) then break end sys.publish("clearworm") Clearworm() updata_freq = 0 sys.wait(300) end elseif cnf.cmd == "timer" then --下发设置光控定时时长参数 setTimer(cnf.ext.tt) sys.wait(300) if not mqttc:publish(pub, upData_120(), serverconf.qos) then break end elseif cnf.cmd == "location" then -- 四情平台下发手动定位 Set_location(packet.payload) if not mqttc:publish(pub, upres("Set the location", "OK"), serverconf.qos) then break end elseif cnf.cmd == "reboot" then -- 四情平台重启 log.warn("Device remote reboot!!!!!") if not mqttc:publish(pub, upres("air820-reboot", "system will restart!!", "ok"), serverconf.qos) then break end sys.restart("Device remote restart") elseif cnf.cmd == "update" then -- 四情平台物联网模块升级 log.warn("Device remote update!!!!!") if not mqttc:publish(pub, upres("air820-updata", "system update will start!!", "ok"), serverconf.qos) then break end Update.run() elseif cnf.cmd == "update_stm32" then -- 四情平台平台主板stm32升级 if not mqttc:publish(pub, upres("update_stm32", "stm32 update will start!!"), serverconf.qos) then break end stm8_update_sw = 1 update_stm32() --STM32远程升级 ------------------------------- elseif cnf.cmd == 'paramconf' then --四情平台下发参数配置 setParamConf(packet.payload) updata_freq = 0 sys.restart("paramconf done then restart!!!") elseif cnf.cmd == 'server_conf' then -- 四情平台服务器配置下发 setServerConf(packet.payload) updata_freq = 0 sys.restart("server_conf done then restart!!!") elseif cnf.cmd == 'thirdserver_conf' then --四情平台下第三方发服务器参数配置 setThirdserverConf(packet.payload) sys.restart("thirdserver_conf done then restart!!!") elseif result and cnf.cmd=="platform" then --四情平台平台切换参数下发 if cnf.ext.type == "120.27.222.26" then nvm.set("platform","120.27.222.26") sys.restart("120.27.222.26") elseif cnf.ext.type == "8.136.98.49" then nvm.set("platform","8.136.98.49") sys.restart("8.136.98.49") end local c = misc.getClock() local date = string.format("%00004d-%02d-%02d %02d:%02d:%02d", c.year, c.month, c.day, c.hour, c.min, c.sec) if not mqttc:publish(pub,upwarn("平台操作","切换平台至:"..cnf.ext.type..",操作时间:"..date), serverconf.qos) then break end end elseif result and cnf.cmd=="sensor" then --温湿度 Setsensor_value(packet.payload) if nvm.get("json_w_stm8boot") ~= "" and nvm.get("json_w_stm8boot") ~= nil then if mqttc:publish(pub, upwarn(nvm.get("json_w_stm8boot"),"主板重启"), serverconf.qos) then nvm.set("json_w_stm8boot","") end end if nvm.get("json_w_stm32_app") ~= "" and nvm.get("json_w_stm32_app") ~= nil then if mqttc:publish(pub, upwarn(nvm.get("json_w_stm32_app"),"输出故障"), serverconf.qos) then nvm.set("json_w_stm32_app","") end end end else log.error("EEEE:::::::::::::not json download::::::::::::::EEEE") end end if packet == "NET_SENT_RDY_" then timeout = 60 log.info("updata is", param) if not mqttc:publish(pub, param, serverconf.qos) then break end end end end mqttc:disconnect() log.info("=============mqtt1 disconnect=============") sys.wait(1000) datalink = 0 -- 服务器断开链接数据指示灯慢闪 end end) -- +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ MQTT2 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ sys.taskInit(function() sys.wait(10*1000) getConfig() -- 开机获取用户配置的参数 log.warn('MQTT2 Task is running!!!!!!!!!!') if thirdserverconf.ip == "" or thirdserverconf.ip == nil then log.info("MQTT2 Ip Not Set!") return end -- 是否获取分配到的ip while not socket.isReady() do log.info("socket2 is not ready,err2_num:", err2_num) err2_num = err2_num + 1 sys.wait(1000) if err2_num >= 600 then log.warn("socket2 connect overtime!") --软件重启(重启原因:socket connect overtime!)注意:重启后的trace中会打印出此重启原因 end end -- 离线消息 willmsg.ext.imei = misc.getImei() will2 = {qos = 1, retain = 0, topic = string.format(thirdserverconf.lastwill .. misc.getImei()), payload = json.encode(willmsg)}-- 创建mqtt客户端--默认配置了MQTT遗愿消息 local mqttc2 = mqtt.client(misc.getImei(), thirdserverconf.keepalive, thirdserverconf.uid, thirdserverconf.pwd, 1, will2) -- 拼接主题 local pub2 = string.format(thirdserverconf.pub .. misc.getImei()) local sub2 = string.format(thirdserverconf.sub .. misc.getImei()) local mqtt2_sta = true while true do mqtt2_sta = mqttc2:connect(thirdserverconf.ip, thirdserverconf.port) log.info('mqtt2 connect status::', mqtt2_sta) if mqtt2_sta == false then log.info("mqtt2 connect fail,try to reconnect!", tcp2_cont) tcp2_cont = tcp2_cont + 1 if tcp2_cont >= 50 then tcp2_cont = 0 sys.restart("mqtt2 reconnect overtime:30!!!") end end -- 订阅主题 if mqttc2:subscribe(sub2, thirdserverconf.qos) then log.warn("------------------------------------------*-*-*-*---*-------------------------------------------") if not mqttc2:publish(pub, upData(), thirdserverconf.qos) then break end log.info("'mqtt2 First upload data is done!!!!!'") log.warn("*********************************************-*-*-*---*-********************************************") sys.wait(2000) while mqtt2_sta==true do local r, packet, param = mqttc2:receive(timeout * 1000 * 60, "NET_SENT_RDY_") if r then -- 这里是有数据下发的处理 local cnf, result, err = json.decode(packet.payload) -- json解析 if result then log.info("::::::::::::::::::::::::::::::::::::::::MQTT2 recv json is::::::::::::::::::::::::::::::::::::::::::", packet.payload) if cnf.cmd == "read" then if cnf.ext == "data" then updata_freq = 0 end -- ++++++下发设置/远程设置++++++ elseif cnf.cmd == "paramconf" then -- 参数配置 if cnf.ext.data_tim ~= nil then -- 平台配置数据上传时间间隔 if not mqttc:publish(pub, upres("xy-dat_f", "Remote set data_tim!!"), serverconf.qos) then break end Set_dattim(packet.payload) sys.wait(300) end if cnf.ext.clt_tim ~= nil then -- 平台配置清虫时间间隔 if not mqttc:publish(pub, upres("xy-clt_f", "Remote set clt_tim!!"), serverconf.qos) then break end Set_clttim(packet.payload) sys.wait(300) end if cnf.ext.work_tim ~= nil then -- 平台配置定时控制参数 if not mqttc:publish(pub, upres("xy-timcotrl", "Remote set work_tim!!"), serverconf.qos) then break end Set_timcontrol(packet.payload) sys.wait(300) end if cnf.ext.power ~= nil then -- 平台开关机控制 if not mqttc:publish(pub, upres("xy-switch", "Remote startup&shutdown action will run!!"), serverconf.qos) then break end setsw(tonumber(cnf.ext.power.ds)) sys.wait(300) end if cnf.ext.location ~= nil then -- 平台下发手动定位 Set_location(packet.payload) if not mqttc:publish(pub, upres("xy-manual_location", "Remote set manual_location!!"), serverconf.qos) then break end end if not mqttc:publish(pub, upData(), serverconf.qos) then break end updata_freq = 0 elseif cnf.cmd == "clearworm" then -- 平台手动下发清虫 if not mqttc:publish(pub, upres("xy-clrworm", "Remote clearworm action will run!!"), serverconf.qos) then break end Clearworm() updata_freq = 0 elseif cnf.cmd == "reboot" then -- 物联网模块重启 if not mqttc:publish(pub, upres("air820-reboot", "System will restart!!"), serverconf.qos) then break end sys.restart("Device remote restart") elseif cnf.cmd == "update" then -- 物联网模块升级 if not mqttc:publish(pub, upres("air820-updata", "System will update!!"), serverconf.qos) then break end Update.run() elseif cnf.cmd == "update_stm32" then -- 四情平台平台主板stm32升级 if not mqttc:publish(pub, upres("update_stm32", "stm32 update will start!!"), serverconf.qos) then break end stm8_update_sw = 1 update_stm32() --STM32远程升级 end end end if packet == "NET_SENT_RDY_" then timeout = 60 log.info("updata is", param) if not mqttc2:publish(pub2, param, thirdserverconf.qos) then break end end end end mqttc2:disconnect() sys.wait(1000) end sys.restart("mqtt2 first publish message is error cause mqtt task is break!") end) -- +++++++++++++++++++++++++++++++++++++++++++++ *网络状况监控任务* ++++++++++++++++++++++++++++++++++++++++++++++++++ -- 网络状况监控任务: sys.taskInit(function() local err = 0 -- 等待设备联网: log.warn("***************socket monitor task is running!***************") while true do while not socket.isReady() do log.warn("socket is not Ready,", "err:", err) err = err + 1 if err >= 600 then sys.restart("socket connect err overtime:30!!!") end sys.wait(1000) end sys.wait(1000) end end) --+++++++++++++++++++++++++++++++++++++++++++++++ * LBS+GPS定位任务 开始* ++++++++++++++++++++++++++++++++++++++++++++++++++ --[[ 功能 :获取基站对应的经纬度后的回调函数 参数 : result:number类型,0表示成功,1表示网络环境尚未就绪,2表示连接服务器失败,3表示发送数据失败,4表示接收服务器应答超时,5表示服务器返回查询失败;为0时,后面的3个参数才有意义 lat:string类型,纬度,整数部分3位,小数部分7位,例如031.2425864 lng:string类型,经度,整数部分3位,小数部分7位,例如121.4736522 返回值:无 ]] -- LBS定位回调函数 GCJ02(火星坐标)-->需转换BD-09(百度坐标) function getLocCb(result, lat, lng) --注意:进入此函数时LBS已经定位成功 if result == 0 then --如果result=0,表示定位成功 log.info("get LBS location success!!!!!!!!!!!!!!!!!!!!!!!!!!!") log.warn("testLbsLoc.getLocCb*****************", result, lat, lng) lbs_loc_lat = lat lbs_loc_lng = lng log.warn("get LBS location message >>>>>>>>>>>>>>>>>>>>>>>>>>", lbs_loc_lat, lbs_loc_lng) gps_status = 2 nvm.set("lat_lbs",lat) nvm.set("lng_lbs",lng) else log.info("get LBS location failed!!!!!!!!!!!!!!!!!!!!!!!!!!!") end end -- GPS日志信息输出函数 WGS-84(国际标准GPS原始坐标)-->需转换BD-09(百度坐标) local function printGps() if gps.isOpen() then local tLocation = gps.getLocation() local speed = gps.getSpeed() log.info("testGps.printGps", gps.isOpen(), gps.isFix(), tLocation.lngType, tLocation.lng, tLocation.latType, tLocation.lat, -- 度格式的经纬度信息 gps.getAltitude(), -- 海拔 speed, -- 速度 gps.getCourse(), -- 方向角 gps.getViewedSateCnt(), -- 可见卫星的个数 gps.getUsedSateCnt()) -- 定位使用的卫星个数 end end ---------------------- GPS 模式切换 ------------------------------ local function test1Cb(tag) log.info("testGps.test1Cb",tag) printGps() end local function test2Cb(tag) log.info("testGps.test2Cb",tag) printGps() end local function test3Cb(tag) log.info("testGps.test3Cb",tag) printGps() end --测试代码开关,取值1,2 local testIdx = 1 local function test(idx) --第1种测试代码 if idx==1 then --执行完下面三行代码后,GPS就会一直开启,永远不会关闭 --因为gps.open(gps.DEFAULT,{tag="TEST1",cb=test1Cb}),这个开启,没有调用gps.close关闭 gps.open(gps.DEFAULT,{tag="TEST1",cb=test1Cb}) --10秒内,如果gps定位成功,会立即调用test2Cb,然后自动关闭这个“GPS应用” --10秒时间到,没有定位成功,会立即调用test2Cb,然后自动关闭这个“GPS应用” gps.open(gps.TIMERORSUC,{tag="TEST2",val=10,cb=test2Cb}) --300秒时间到,会立即调用test3Cb,然后自动关闭这个“GPS应用” gps.open(gps.TIMER,{tag="TEST3",val=300,cb=test3Cb}) --第2种测试代码 elseif idx==2 then --执行完下面三行代码打开GPS后,5分钟之后GPS会关闭 gps.open(gps.DEFAULT,{tag="TEST1",cb=test1Cb}) sys.timerStart(gps.close,300000,gps.DEFAULT,{tag="TEST1"}) gps.open(gps.TIMERORSUC,{tag="TEST2",val=10,cb=test2Cb}) gps.open(gps.TIMER,{tag="TEST3",val=60,cb=test3Cb}) end end -------------------------------------------------------------------- local function nmeaCb(nmeaItem) log.info("testGps.nmeaCb",nmeaItem) end -- GPS+LBS定位任务 sys.subscribe("AUTOGPS_READY",function(gpsLib,agpsLib,kind,baudrate) gps=gpsLib agps=agpsLib log.info("testGps.AUTOGPS_READY",baudrate,kind) gps.setUart(uartId,baudrate,8,uart.PAR_NONE,uart.STOP_1) -- 设置串口通信参数,波特率为自适应 gps.setNmeaMode(2,nmeaCb) -- gps.lua和外部程序都处理NEMA数据 test(testIdx) sys.timerLoopStart(printGps,2000) end) sys.taskInit( function() while true do gps_status = 0 locat_cnt = 0 sys.wait(8 * 1000) -- 等待socket连接完毕 while true do if tonumber(manual_location.type) == 0 then -- 判断是否手动定位 若手动定位直接关闭GPS if socket.isReady() and gps_status ~=1 and gps_status ~= 2 then log.warn("================ LBS Location successful ===============") lbsLoc.request(getLocCb) sys.wait(1000) end if gps.isFix() == false then log.info("================ GPS Location failed ===============") printGps() elseif gps.isFix() == true then gps_cont = gps_cont + 1 local location = gps.getLocation() gps_loc_lat = location.lat gps_loc_lng = location.lng printGps() if gps_cont >= 3 then -- 获取3次gps定位数据的最后一次 nvm.set("lat_gps",gps_loc_lat) nvm.set("lng_gps",gps_loc_lng) gps.closeAll() end gps_status = 1 log.info("================ GPS Location successful ===============") end sys.wait(1000) log.info("GPS open status is:", gps.isOpen()) log.info("GPS location status is:", gps.isFix()) else gps_status = 0 gps.closeAll() sys.wait(2000) end sys.wait(1000) locat_cnt = locat_cnt + 1 if locat_cnt >= 1800 then -- 每隔30分钟判断一下定位,若失败,则break if (gps_loc_lng == "0" and gps_loc_lat == "0") and (lbs_loc_lat == "0" and lbs_loc_lng == "0") then break else locat_cnt = 0 log.warn("location normal !!!") end end end end end ) ------------------------------------------------------ * LBS+GPS定位任务 结束* ------------------------------------------------ --++++++++++++++++++++++++++++++++++++++++++++++++++++ * SIM卡自动切换线程 * +++++++++++++++++++++++++++++++++++++++++++++++++++ local function cbFnc(result) if result then log.info("SIM switch successful") else log.info("SIM switch failed") end end -- 说明:目前版本不支持SIM自动切换功能需手动切换SIM卡 -- 注意:本命令关机保存,但是需重启生效 -- 初次刷入程序默认SIM ID = 0 sys.taskInit( function() sys.wait(5 * 1000) -- 注意:开机lua脚本运行之后,会发送at命令去查询id,所以需要一定时间才能获取到id。开机后立即调用此接口,基本上返回nil local ID1 = sim.getId() local ID2 = ID1 log.info("Now SIM is:::", ID1) if ID1 == 0 then ID2 = 1 elseif ID1 == 1 then ID2 = 0 end sys.wait(5 * 1000) while true do if sim.getStatus() == false or sim.getStatus() == nil then -- 切换SIM卡 sim.setId(ID2,cbFnc) sys.wait(1000) sim.setId(ID2,cbFnc) sys.restart("switch sim card") end local id = sim.getId() -- 获取目前设置的双卡单待id log.info("Now system SIM card is:::", id) sys.wait(5 * 1000) end end ) --+++++++++++++++++++++++++++++++++++++++++++++++ * MQTT守护线程 * ++++++++++++++++++++++++++++++++++++++++++++++++ -- Mqtt异常监测 sys.taskInit(function() sys.wait(10*1000) local dev_dta_on = 1 while true do if mqtt_status == "" then mqtt_status_num = mqtt_status_num + 1 elseif mqtt_status == "true" then mqtt_status = "" mqtt_status_num = 0 sys.wait(1000) end if mqtt_status_num > timeout * 61 then sys.restart("MQTT ERROR!!!") end log.warn("====================mqtt_check=================:",mqtt_status_num,mqtt_status,timeout) sys.wait(1000) end end) --------------------------------------------------------------- --定时上报任务 sys.taskInit( function() sys.wait(15*1000) if dat_f ==0 or dat_f == nil or dat_f =="" then dat_f = 30 end while true do updata_freq = dat_f * 60 while updata_freq ~= 0 do updata_freq = updata_freq - 1 sys.wait(1000) log.info("++++++++ 1 !!!!!!!!") end if serverconf.ip == "8.136.98.49" then sys.publish("NET_SENT_RDY_", upData()) infrared_count = 0 ClearKcnt() -- 上报数据清除电机次数 log.info("++++++++ 2 !!!!!!!!") elseif serverconf.ip == "120.27.222.26" then sys.publish("NET_SENT_RDY_", upData_120()) sys.publish("NET_SENT_RDY_", upStatus()) infrared_count = 0 ClearKcnt() -- 上报数据清除电机次数 log.info("++++++++ 3 !!!!!!!!") end sys.wait(100) log.info("+++++++++ 4 !!!!!!!!") end end ) -- 每隔5秒更新主板数据and打印 sys.taskInit(function() sys.wait(5 * 1000) while true do log.warn("................................Mainboard-uart 通信中1....................................") PrintData() --getStatus() local firmware_name = rtos.get_version() -- 获取底层固件版本 local space = rtos.get_fs_free_size() -- 获取文件系统剩余空间(单位Bytes) local netmode = net.getNetMode() -- 4:4G LTE网络 local SIMS = sim.getStatus() -- 获取sim卡的状态 log.warn("Clear worm time is:", clt_t) log.warn("Data time is:", dat_f) log.warn("Now firmware version is:", firmware_name .. " PROJECT:" .. _G.PROJECT .. " VERSION:" .. _G.VERSION) log.warn("File system free space:", space) log.warn("Net mode is:", netmode) log.warn("Sim status is:", SIMS) sys.wait(5 * 1000) end end) --++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- 重启预警函数 function getRebootState() rebootstate = io.readFile(DEV_REBOOT) -- 开机获取设备启动次数 rebootinfo = io.readFile(DEVICE_ERR) -- 开机获取设备软件重启原因 if rebootstate == nil then log.info("first startup!!!!!!!!") rebootstate = 0 end rebootstate = rebootstate + 1 io.writeFile(DEV_REBOOT, rebootstate) end --------------------------------------------光栅计数线程--------------------------------------------------- sys.taskInit(function() -- GPIO中断处理函数(修正递归调用问题) local function gpioInterruptHandler(msg) log.info("GPIO中断", "触发类型:", msg) if msg == cpu.INT_GPIO_POSEDGE then if result_crc.ds == 1 then infrared_count = infrared_count + 1 -- 操作局部变量 log.info("红外计数器", "当前值:", infrared_count) log.info("GPIO_2", "检测到上升沿触发") else infrared_count = 0 end else log.info("GPIO_2", "非上升沿触发事件") end end -- 配置GPIO引脚及中断 local function setupGPIO() log.info("GPIO初始化", "开始配置P0_2...") local pin = pins.setup(pio.P0_2, gpioInterruptHandler,pio.PULLUP)-- 绑定处理函数 if not pin then log.error("GPIO配置", "P0_2初始化失败!") return false end log.info("GPIO配置", "P0_2上升沿中断已启用") return true end -- 主任务逻辑 if setupGPIO() then while true do sys.wait(1000) -- 示例:每1秒输出当前计数 log.info("状态报告", "累计触发次数:", infrared_count) end else log.error("任务终止", "GPIO初始化失败") end end) -- function Interrupt_re(msg) -- log.info("testGpioSingle.gpio2IntFnc",msg,Interrupt_re()) -- log.info("first infrared_count!!!!!!!!") -- if msg == cpu.INT_GPIO_POSEDGE then -- infrared_count = infrared_count + 1 -- log.info("infrared_count", infrared_count) -- log.info("GPIO_2 被触发") -- else -- log.info("GPI0_2 未触发") -- end -- end -- Interrupt_re = pins.setup(pio.P0_2,Interrupt_re,pio.PULLUP) --------------------------------------------光栅计数线程--------------------------------------------------- ---+++++++++++++++++++++++++++++++++++++++++++++ * Mainboard-uart 通信中 * ++++++++++++++++++++++++++++++++++++++++++++++++++++++++ --每隔10秒打印输出 sys.taskInit( function() getRebootState() sys.wait(100) while true do log.warn("................................Mainboard-uart 通信中....................................") PrintData() sys.wait(5 * 1000) end end ) --BootLoader交互信息下发 sys.taskInit( function() sys.wait(500) while true do if BootLoader_flag == 1 then BootLoader_flag = 0 log.info("BootLoader_flag",BootLoader_flag) BootLoader_stm32() log.info("stm32 SerialDownload !!!") end if upgrade_again == 1 then log.info("update_stm32 system will upgrade again !!!") update32.run() end sys.wait(500) end end ) --串口通讯心跳交互 sys.taskInit( function() sys.wait(100) local uart_flag_count = 0 local uart_32 = string.char(0xCC,0XDD) while true do if uart_flag == 1 then uart_flag = 0 uart_flag_count = uart_flag_count + 1 if uart_flag_count > 5 then uart_flag_count = 0 uart.write(1,uart_32) log.info("uart_flag back!!!!") end end sys.wait(50) end end ) -- 串口缓冲区最大值 local SENDSIZE = 128 --串口写空闲 local writeIdle = {true} --数据发送的消息队列 recvBuff = {{}} local writeBuff = {{}} local uartReadTime = 50 -- 串口读超时 local flowCount = {0, 0} local uid = 1 -- 写标志位 local function writeDone() if #writeBuff[1] == 0 then writeIdle[1] = true sys.publish("UART_" .. 1 .. "_WRITE_DONE") log.warn("UART_" .. uid .. "write done!") else writeIdle[1] = false uart.write(1, table.remove(writeBuff[1], 1)) log.warn("UART_" .. 1 .. "writing ...") end end -- uart 写 function write(str) if not str or str == "" or str == nil then return end if str ~= true then for i = 1, #str, SENDSIZE do table.insert(writeBuff[1], str:sub(i, i + SENDSIZE - 1)) end log.warn("uart" .. 1 .. ".write data length:", writeIdle[1], #str) end if writeIdle[1] and writeBuff[1] then local str = table.concat(writeBuff[1]) table.remove(writeBuff[1], 1) while true do uart.write(1, str) break end log.warn("UART_" .. uid .. "writing ...") end end local function read(s) local s = table.concat(recvBuff[1]) local idx, tmp = 1 local conf = s recvBuff[1] = {} -- 串口流量统计 flowCount[1] = flowCount[1] + #s log.info("UART_" .. 1 .. "read length:", #s) log.info("串口流量统计值:", flowCount[1]) log.info("UART:",s,string.toHex(s)) if updateflag == 1 then log.info(s) sys.publish("YM_IS_OK", s) return end if s:find("update") then --判断是否进入升级模式 updateflag = 1 if update32.updateok == 0 then s = upwarn("device_stm32", "system will update") sys.publish("NET_SENT_RDY_", s) else s = upwarn("device_stm32", "system is updating......") sys.publish("NET_SENT_RDY_", s) end log.info("update_stm32 system will update !!!") update32.run() end if s:find("bootflag") then --重复远程升级标志位 upgrade_again = 1 end if flowCount[1] == 64 then --串口通讯心跳检测 uart_flag = 1 end if s:find("Lamp_fauit") then --判断灯管是否故障 local c = misc.getClock() local date = string.format("%00004d-%02d-%02d %02d:%02d:%02d", c.year, c.month, c.day, c.hour, c.min, c.sec) log.info("检测到灯管故障!!!") nvm.set("json_w_stm32_app","检测到杀虫灯LED灯管短路:".."故障时间:"..date) end if s:find("App") then --判断主板是否复位 local c = misc.getClock() local date = string.format("%00004d-%02d-%02d %02d:%02d:%02d", c.year, c.month, c.day, c.hour, c.min, c.sec) log.info("检测到stm32复位!!!") nvm.set("reboot_stm8",nvm.get("reboot_stm8")+1) nvm.set("json_w_stm8boot","检测到主板复位,总复位次数:"..nvm.get("reboot_stm8").."复位时间:"..date) end if #conf == nil or #conf == 0 or conf:len() == 64 then log.info("getParam len,value:", string.toHex(conf, " ")) -- 将返回的数据填充到result表 result.ver = string.sub(conf, 49,63) -- 软件版本-FX-SCD-U-V1.0 idx, result.iSave = pack.unpack(conf, "b", idx) -- eeprom标志位 if result.iSave ~= 0xAA then return end -- 判断chuankou上传数据格式是否正确 idx, result_crc.ds = pack.unpack(conf, ">b", idx) -- 设备状态 if(result_crc.ds==0 or result_crc.ds==1) then result.ds = result_crc.ds end idx, result_crc.tt = pack.unpack(conf, "b", idx) -- 光控时长小时 if(result_crc.tt>=0 and result_crc.tt<8) then result.tt = result_crc.tt end idx, result_crc.ws = pack.unpack(conf, "b", idx) -- 工作状态 if(result_crc.ws==0 or result_crc.ws==1 or result_crc.ws==2) then result.ws = result_crc.ws end idx, result_crc.lps = pack.unpack(conf, "b", idx) -- 光控状态 if(result_crc.lps==0 or result_crc.lps==1) then result.lps = result_crc.lps end idx, result_crc.rps = pack.unpack(conf, "b", idx) -- 雨控状态 if(result_crc.rps==0 or result_crc.rps==1) then result.rps = result_crc.rps if(result_crc.rps==1 and rps_y==0) then rps_x = 1 elseif(result_crc.rps==0) then rps_y = 0 end end idx, result_crc.tps = pack.unpack(conf, "b", idx) -- 温控状态 if(result_crc.tps==0 or result_crc.tps==1 or result_crc.tps==2) then result.tps = result_crc.tps end idx, result_crc.dps = pack.unpack(conf, "b", idx) -- 倾倒保护 if(result_crc.dps==0 or result_crc.dps==1) then result.dps = result_crc.dps end idx, result_crc.vps = pack.unpack(conf, "b", idx) -- 电压状态 if(result_crc.vps==0 or result_crc.vps==1 or result_crc.vps==2) then result.vps = result_crc.vps end idx, result.lcm = pack.unpack(conf, "b", idx) -- 光控类型类型 idx, result.Lamp = pack.unpack(conf, 'b', idx) -- 灯管故障检测 idx, result.Infrared = pack.unpack(conf, 'b', idx) -- 红外传感器 idx, result.kcnt = pack.unpack(conf, "0 and result_crc.kcnt<9000) then result.kcnt = result_crc.kcnt end idx, result.cleartim = pack.unpack(conf, 'b', idx) -- 清虫时间间隔 idx, result.clear_on = pack.unpack(conf, 'b', idx) -- 自清虫标志位 idx, result.cycle_off = pack.unpack(conf, '0 and result_crc.cv<30000) then result.cv = result_crc.cv if result.cv < 500 then result.cv = 0 end end idx, result_crc.bv = pack.unpack(conf, "0 and result_crc.bv<30000) then result.bv = result_crc.bv end idx, result.bt = pack.unpack(conf, " flow then uart.on(1, "receive") log.info("uart1.read length count:", flowCount[1]) end end if timecnt > 10 then timecnt = 1 flowCount = {0, 0} else timecnt = timecnt + 1 end end, 1000 ) --*********************开机运行************************** uart_INIT()