| 123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218219220221222223224225226227228229230231232233234235236237238239240241242243244245246247248249250251252253254255256257258259260261262263264265266267268269270271272273274275276277278279280281282283284285286287288289290291292293294295296297298299300301302303304305306307308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347 |
- /*
- * Copyright (c) 2006-2020, RT-Thread Development Team
- *
- * SPDX-License-Identifier: Apache-2.0
- *
- * Change Logs:
- * Date Author Notes
- * 2020-05-30 Administrator the first version
- */
- #ifndef APPLICATIONS_INC_CONTROL_H_
- #define APPLICATIONS_INC_CBD_CONTROL_H_
- #include <rtthread.h>
- #include <board.h>
- #include <rtdevice.h>
- //定制相关//////////////////////////////////////////////////////
- #define LAMP_EN 0 //李新3灯管:0关闭,1打开
- #define SENSOR_EN 1 //温湿度:0关闭,1打开
- #define ROBOT_EN 0 //机器人
- #define Color_EN 0 //定制色诱
- #define BZYV2_EN 0 //孢子仪2.0
- ////////////////////////////////////////////////////////////////
- #if LAMP_EN == 1
- #define VERSION_HK "1.(3ledv6).41(HK)" //4.0海康-三色光源
- #else
- #define VERSION_HK "1.49.41(HK)" //4.0海康-1200W
- #endif
- #define VERSION_HK_4800W "1.48.48(HK)" //4.0海康-4800W
- #define VERSION_HK_2000W "1.46.4(2000W)" //4.0水稻
- #define VERSION_ZP "1.41.1(ZP)" //1.0转盘
- #define VERSION_GK "1.38.1(GK)" //1.0高空
- #define VERSION_XCT "1.13.6(HK)" //吸虫塔-海康
- #define VERSION_V5 "1.2.5(HK)" //5.0
- #define VERSION_Robot "1.0(robot)" //展厅机器人
- #define VERSION_BZY "2.4" //孢子仪
- #define CompileTime rt_sprintf(device_status.driver_compile,"%s-%s",__DATE__,__TIME__) //编译时间,每次更新代码修改
- /*********************************************************************/
- typedef struct
- {
- uint8_t iSave; //存储标志位
- uint8_t dtype; //设备类型?7-孢子仪,3-测报灯
- /*孢子仪*/
- uint8_t run_sta; //转盘的位置:0原始;1收集;2培养;3拍照;4凡士林,其他-测试
- uint8_t cul_time; //培养时间
- uint8_t stay_time; //已培养时间
- uint8_t pre_temp; //培养仓温度
- uint8_t box_temp; //箱体温度
- uint8_t auto_test_sw; //一键测试 0-关 1-开
- uint8_t cold_status; //制冷状态 0-关 1-开
- uint8_t cold_sw; //制冷开关 0-关 1-开
- uint8_t wind_sw; //风机开关 0-关 1-开
- uint8_t collect_fan_status; //采集状态 0-关 1-开
- uint8_t autotakepic; //对焦拍照 0-关 1-开
- uint8_t develop_flag; //是否进入培养模式
- uint8_t cool_fan_status; //散热风机状态 0-停止 1-打开
- uint8_t fsl_sw; //凡士林开关:0-关,1-开
- uint8_t collecting_sh1; //采集开启1
- uint8_t collecting_eh1; //采集关闭1
- uint8_t collecting_sh2; //采集开启2
- uint8_t collecting_eh2; //采集关闭2
- uint8_t collecting_sh3; //采集开启3
- uint8_t collecting_eh3; //采集关闭3
- /*测报灯*/
- uint8_t heat_sw; //加热开关
- uint8_t photo_ws; //拍照
- uint8_t power_status; //电源
- uint8_t sun_test; //光控测测试标志位
- uint8_t heat_status; //加热状态 0-关 1-开
- uint8_t lamp_status; //灯管1状态 0-关 1-开
- uint8_t lamp1_status; //灯管2状态 0-关 1-开
- uint8_t lamp2_status; //灯管3状态 0-关 1-开
- uint8_t up_status; //上仓门状态 0-停止 1-打开 2-关闭
- uint8_t down_status; //下仓门状态 0-停止 1-打开 2-关闭
- uint8_t clear_status; //清扫状态 0-停止 1-开始
- uint8_t shake_ws; //震动 0-关 1-开
- uint8_t heatvalue; //加热设定温度
- uint8_t ctr_up_motor; //上仓门, 1打开,0关闭
- uint8_t ctr_down_motor; //下仓门, 1打开,0关闭
- uint8_t rain_status; //雨控 0-正常 1-欠压
- uint8_t temp_status; //温控 0-正常 1-温控
- uint8_t sun_status; //光控 0-正常 1-光控
- uint8_t ds; //设备状态 0-关机 1-开机
- uint8_t work_status; //工作状态 0-待机 1-工作
- uint8_t work_done; //工作结束 1-正常 0-工作已结束
- uint8_t bat_status; //电压状态 1-正常 0-欠压
- uint8_t heattime; //加热时间
- uint8_t heat_time_min; //实时加热时间
- uint8_t clt_time; //收集时间
- uint8_t vol; //音量
- uint8_t refresh_num; //DTU数据刷新时间
- uint8_t refresh_timeout; //刷新超时时间
- uint8_t sunBar; //光控定时时间
- uint8_t startBar; //时控开始时间
- uint8_t stopBar; //时控结束时间
- uint8_t tph; //高温保护
- int8_t tpl; //低温保护
- uint8_t timeSwitch; //模式0光控,1时控
- uint8_t link_sta; //有线接入状态:0-未接入,1已接入
- uint8_t heattem; //加热仓温度(实时)
- uint8_t hmi_fresh; //是否启动屏幕
- uint8_t update_flag; //是否启动升级
- uint8_t photo_type; //相机类型,0-USB,1-海康,2-大华
- uint8_t version_type; //版本类型,1-转盘,4-海康,41-水稻,11-高空,48-4800
- uint8_t stop_in_bootloader; //进入bootloader模式 1
- uint8_t account_status; //卡状态
- uint8_t test_flag; //测试标志
- uint8_t sensor_485_sta; //485传感器
- //孢子仪2.0
- uint8_t step_focus;
- uint16_t dattim; //数据上传间隔
- uint16_t shake_sec; //震动时间
- uint16_t thsp; //息屏时间
- rt_uint32_t num_updata; //
- rt_uint32_t rebootcnt; //启动次数
- rt_uint32_t light_over_tim; //光控定时差秒数,镇流器的结束时间
- rt_uint32_t data_plan; //流量套餐
- rt_uint32_t expiry_date; //到期时间
- double focus_value;
- int passWord; //初始密码
- const char *coll_time[10];
- char mqttcfg1[64]; //
- char mqttcfg2[64]; //
- char csq[8]; //信号强度
- char net[8]; //网络
- char sim[8]; //SIM卡
- char gps[8]; //定位类型
- char tempture[12]; //温度
- char humidity[12]; //湿度
- char driver[64]; //版本
- char driver_4g[64]; //4g版本
- char driver_bl[64]; //BL版本
- char driver_compile[64]; //BL编译时间
- char project[32]; //project,用于判断升级
- char lng[32]; //经度
- char lat[32]; //纬度
- char stamp[32]; //系统时间
- char fuse_voltage[32]; //保险丝电压
- char iccid[32]; //SIM卡ICCID
- char imei[32]; //IMEI,唯一ID
- char json_w_clock[128]; //修改时间
- char json_w_reset[128]; //
- char json_w_platform[128]; //
- char power[8]; //功率
- char voltage[8]; //电池电压
- }Device_Status_typedef;
- /**************滑台数据********************/
- typedef struct
- {
- uint32_t xdis; //x轴坐标移动距离
- uint32_t ydis;
- uint32_t zdis; //z轴坐标移动距离
- uint16_t dxdis; //x轴坐标蛇形移动间距距离
- uint16_t dzdis; //z轴坐标蛇形移动间距距离
- uint8_t xdir; //x轴坐标移动方向
- uint8_t ydir;
- uint8_t zdir; //z轴坐标移动方向
- uint8_t en_slide; //z轴坐标移动方向
- uint8_t zccwl_on; //z轴限位开关信号 高电平为触发限位
- uint8_t xccwl_on; //x轴限位开关信号 高电平为触发限位
- uint8_t pulse_period; //滑台的运动速度 1为最高
- uint8_t stop_flag; //滑台停止标志位
- }Device_slide_typedef;
- /************************************************/
- #define ON 1
- #define OFF 0
- #define LED0_PIN GET_PIN(B, 3)
- #define Beep GET_PIN(B, 4)
- #define OPEN 0x02
- #define CLOSE 0x03
- /************************************************/
- //光控
- #define LIGHT_PIN GET_PIN(C,0)
- //雨控
- #define RAIN_PIN GET_PIN(C,1)
- //加热
- #define Heat_Pin GET_PIN(B,12)
- //采集/上仓门
- #define Collect_fan_R GET_PIN(C, 5)
- #define Collect_fan_L GET_PIN(C, 4)
- //下仓门
- #define C_DOWN_R GET_PIN(B,0)
- #define C_DOWN_L GET_PIN(B,1)
- //镇流器
- #define LAMP_SW GET_PIN(C,9)
- //震动电机
- #define SHAKE_SW GET_PIN(B,2)
- //补光
- #define LED_SW GET_PIN(A,15)
- //清扫
- #define CLEAR_R GET_PIN(C,7)
- #define CLEAR_L GET_PIN(C,8)
- //相机供电
- #define PHOTO GET_PIN(A,12)
- //路由器供电
- #define ROUTER GET_PIN(A,8)
- //RTU/DTU供电
- #define RTU_DTU GET_PIN(B,13)
- //海康相机拍照
- #define HK_TAKE GET_PIN(A,11)
- #define HK_IO GET_PIN(B,14) //备用触发拍照
- //清扫限位
- #define CLEAR_R_LIMIT GET_PIN(C,13)
- #define CLEAR_L_LIMIT GET_PIN(B,9)
- /*****************************4.0定制多光源*********************************/
- #define LAMP_1_SW GET_PIN(B,10)
- #define LAMP_2_SW GET_PIN(B,11)
- /***************************高空测报灯*************************/
- //上仓门电机限位
- #define CTR_UPO_LIMIT GET_PIN(C,13)
- #define CTR_UPC_LIMIT GET_PIN(B,9)
- //下仓门电机限位
- #define CTR_DWO_LIMIT GET_PIN(B,5)
- #define CTR_DWC_LIMIT GET_PIN(B,8)
- //雨控电机限位,控制排水和落虫
- #define CTR_RO_LIMIT GET_PIN(B,15)
- #define CTR_RC_LIMIT GET_PIN(C,6)
- /******************************吸虫塔*********************************/
- #define HK_5000W_P GET_PIN(B,12)
- #define ROUTER_P GET_PIN(B,10)
- #define LED_P GET_PIN(B,11)
- #define PC7_TIM3_CH 2 //pwm8
- #define PC8_TIM3_CH 3 //pwm8
- #define PB1_TIM3_CH 4 //pwm3
- #define MOTOR1_CTR_PIN GET_PIN(C,9) //吸虫电机IO
- #define MOTOR2_CTR_PIN GET_PIN(B,2) //吸附电机IO
- #define MOTOR_CR_PIN GET_PIN(C,7)
- #define MOTOR_CL_PIN GET_PIN(C,8)
- #define MOTOR_C_LIMIT GET_PIN(C,13) //卷带限位
- void ctr_JD_Clear(uint8_t shake_sw);
- uint8_t ctr_Motor_xichong(uint8_t status_ws);
- uint8_t ctr_Motor_xifu(uint8_t status_ws);
- uint8_t ctr_Camera_Power(uint8_t status_ws);
- /*****************************5.0测报灯******************************/
- void ctr_turnv5(void);
- /*****************************孢子仪**********************************/
- //制冷
- #define Cold_Pin GET_PIN(B,11)
- //采集
- #define Collect_Fan GET_PIN(B,10)
- //转盘
- #define TURN_ZP_R GET_PIN(B,0)
- #define TURN_ZP_L GET_PIN(B,1)
- //转盘限位
- #define LIMIT_0 GET_PIN(C,13)
- #define LIMIT_90 GET_PIN(B,9)
- //散热
- #define Cool_Fan_R GET_PIN(C, 5)
- #define Cool_Fan_L GET_PIN(C, 4)
- //步进电机限位
- #define LIMIT_UP GET_PIN(B,8)
- #define LIMIT_DOWN GET_PIN(B,5)
- //步进电机驱动
- #define Motor_EN GET_PIN(B,14)
- #define Motor_DIR GET_PIN(B,15)
- void ctr_turn(uint8_t v,uint8_t sta);
- uint8_t ctr_Cold(uint8_t status_cold);
- uint8_t ctr_Cool_Fan(uint8_t status_cool); //散热风机
- uint8_t ctr_Collect_Fan(uint8_t status_collect); //采集风机
- void ctr_Motor_Driver(uint8_t EN,uint8_t DIR,rt_uint32_t pwm,rt_uint32_t time_out); //步进电机
- void ctr_Petroleum_jelly(rt_uint32_t delay); //凡士林
- /*****************************定制4.0-2000W***************************************/
- #define FAN_P GET_PIN(B,10)
- #define FAN_I GET_PIN(B,11)
- uint8_t ctr_Fan_IN(uint8_t status_ws);
- uint8_t ctr_Fan_PUT(uint8_t status_ws);
- /*******************************定制展厅机器人************************************/
- #define LIMIT_OPEN GET_PIN(B,8)
- #define LIMIT_CLOSE GET_PIN(B,5)
- #define Motor_Power GET_PIN(B,10) //电机驱动供电
- #define Motor_Direction_Button GET_PIN(B,9) //IO输入,X轴限位
- #define Motor_Direction_Ctr GET_PIN(B,15) //IO输出,控制电机运动方向
- #define EMS_Dir GET_PIN(B,14)
- void ctr_Motor_Robot(uint8_t status_ws);
- /****************************定制色诱***************************************************/
- #define LIMIT_RESET GET_PIN(C,13)
- #define LIMIT_BOARD GET_PIN(B,9)
- #define KEY_RESET GET_PIN(B,8)
- #define KEY_BACK GET_PIN(B,5)
- int ctr_Color_board(uint8_t forward,uint16_t time_board);
- /***************************************************************/
- /***************************************************************/
- uint8_t ctr_Heat(uint8_t status_heat); //加热
- uint8_t ctr_cangmen_up(uint8_t status_up); //上仓门
- uint8_t ctr_cangmen_down(uint8_t status_down); //下仓门
- uint8_t ctr_lamp(uint8_t status_lamp,uint8_t lamp_num); //镇流器
- uint8_t ctr_shake(uint8_t status_shake,uint16_t shake_sec); //震动
- uint8_t ctr_clear(uint16_t status_clear); //清扫
- void ctr_TG_Clear(uint16_t clear_timeout); //清扫2
- uint8_t ctr_led(uint8_t status_led); //补光灯
- void calorstat(uint16_t heat_time); //恒温
- void ctr_router(uint8_t status_router); //路由器
- void turnzp(void); //转仓
- void Hk_Take_io(void); //触发拍照
- void HK_TakePhoto(void); //拍照
- void ctr_photo(uint8_t status_photo);
- void ctr_RTU_DTU(uint8_t status_rtu);
- void HardWare_Init(uint8_t boot); //初始化
- void HardWare_Check(uint8_t boot); //自检
- void ResetInit(void); //上电复位
- void SunTest(void); //光控测试
- /*****************************************************/
- void WorkTask_XCT(void);
- /****************************************************/
- void WorkCheck(void); //工作检测
- void WorkTask(void); //工作任务
- //
- /***********************孢子仪2.0****************************/
- #define X_ 0
- #define Y_ 1
- #define Z_ 2
- #define Limit_Motor_X GET_PIN(B,9) //IO输入,X轴限位
- #define Limit_Motor_Z GET_PIN(C,13) //IO输入,Y轴限位
- #define Limit_Motor_Y GET_PIN(B,8) //IO输入,Z轴限位
- uint8_t ctr_swz(uint8_t status_swz); //z轴的电机开关控制
- uint32_t ctr_move(uint8_t DIR_,uint8_t dir_,uint32_t dis_,uint8_t pulse);
- void slidelock(); //电机移动完毕后上锁
- void turnlimit(void); //位移兼限位开关功能
- /***************************************************/
- //线程
- int Control_clear(void);
- int Workstatus_check(void);
- int Work_Loop_Task(void);
- int Control_heat(void);
- int slide_Fresh(void);
- #endif /* APPLICATIONS_INC_CONTROL_H_ */
|