control.h 9.0 KB

123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960616263646566676869707172737475767778798081828384858687888990919293949596979899100101102103104105106107108109110111112113114115116117118119120121122123124125126127128129130131132133134135136137138139140141142143144145146147148149150151152153154155156157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208209210211212213214215216217218
  1. /*
  2. * Copyright (c) 2006-2020, RT-Thread Development Team
  3. *
  4. * SPDX-License-Identifier: Apache-2.0
  5. *
  6. * Change Logs:
  7. * Date Author Notes
  8. * 2020-05-30 Administrator the first version
  9. */
  10. #ifndef APPLICATIONS_INC_CONTROL_H_
  11. #define APPLICATIONS_INC_CBD_CONTROL_H_
  12. #include <rtthread.h>
  13. #include <board.h>
  14. #include <rtdevice.h>
  15. //定制相关//////////////////////////////////////////////////////
  16. #define LAMP_EN 0 //李新3灯管:0关闭,1打开
  17. #define SENSOR_EN 1 //温湿度:0关闭,1打开
  18. ////////////////////////////////////////////////////////////////
  19. #if LAMP_EN == 1
  20. #define VERSION_HK "1.(3ledv3).41(HK)" //4.0海康-三色光源
  21. #else
  22. #define VERSION_HK "1.44.41(HK)" //4.0海康
  23. #endif
  24. #define VERSION_HK_2000W "1.41.4(2000W)" //4.0水稻
  25. #define VERSION_ZP "1.38.1(ZP)" //1.0转盘
  26. #define VERSION_GK "1.38.1(GK)" //1.0高空
  27. #define VERSION_XCT "1.9.6(HK)" //吸虫塔-海康
  28. #define VERSION_V5 "1.2.5(HK)" //5.0
  29. #define CompileTime rt_sprintf(device_status.driver_compile,"%s-%s",__DATE__,__TIME__) //编译时间,每次更新代码修改
  30. /*********************************************************************/
  31. typedef struct{
  32. uint8_t iSave; //存储标志位
  33. uint8_t dtype; //设备类型
  34. uint8_t photo_ws;
  35. uint8_t power_status;
  36. uint8_t sun_test;
  37. uint8_t sensor_sta; //0-正常,1-平台获取温湿度
  38. uint8_t heat_status; //加热状态 0-关 1-开
  39. uint8_t lamp_status; //灯管1状态 0-关 1-开
  40. uint8_t lamp1_status; //灯管2状态 0-关 1-开
  41. uint8_t lamp2_status; //灯管3状态 0-关 1-开
  42. uint8_t up_status; //上仓门状态 0-停止 1-打开 2-关闭
  43. uint8_t down_status; //下仓门状态 0-停止 1-打开 2-关闭
  44. uint8_t clear_status; //清扫状态 0-停止 1-开始
  45. uint8_t shake_ws; //震动 0-关 1-开
  46. uint8_t heatvalue; //
  47. uint8_t ctr_up_motor; //上仓门, 1打开,0关闭
  48. uint8_t ctr_down_motor; //下仓门, 1打开,0关闭
  49. uint8_t rain_status; //雨控 0-正常 1-欠压
  50. uint8_t temp_status; //温控 0-正常 1-温控
  51. uint8_t sun_status; //光控 0-正常 1-光控
  52. uint8_t ds; //设备状态 0-关机 1-开机
  53. uint8_t work_status; //工作状态 0-待机 1-工作
  54. uint8_t work_done; //工作结束 1-正常 0-工作已结束
  55. uint8_t bat_status; //电压状态 1-正常 0-欠压
  56. uint8_t heattime; //加热时间
  57. uint8_t heat_time_min; //实时加热时间
  58. uint8_t clt_time; //收集时间
  59. uint8_t vol; //音量
  60. uint16_t thsp; //息屏时间
  61. uint8_t refresh_num; //DTU数据刷新时间
  62. uint8_t refresh_timeout;//刷新超时时间
  63. uint8_t sunBar; //光控定时时间
  64. uint8_t startBar; //时控开始时间
  65. uint8_t stopBar; //时控结束时间
  66. uint8_t tph; //高温保护
  67. int8_t tpl; //低温保护
  68. uint16_t shake_sec; //震动时间
  69. uint8_t timeSwitch; //模式0光控,1时控
  70. uint8_t link_sta; //有线接入状态:0-未接入,1已接入
  71. uint16_t dattim; //数据上传间隔
  72. uint8_t heattem; //加热仓温度(实时)
  73. uint8_t hmi_fresh; //是否启动屏幕
  74. uint8_t update_flag; //是否启动升级
  75. uint8_t photo_type; //相机类型,0-USB,1-海康,2-大华
  76. uint8_t version_type; //版本类型,1-转盘,4-海康,42-水稻,11-高空
  77. uint8_t stop_in_bootloader; //进入bootloader模式 1
  78. uint8_t account_status; //卡状态
  79. uint8_t test_flag; //测试标志
  80. uint8_t sensor_485_sta; //485传感器
  81. rt_uint32_t num_updata; //
  82. rt_uint32_t rebootcnt; //启动次数
  83. rt_uint32_t light_over_tim; //光控定时差秒数,镇流器的结束时间
  84. rt_uint32_t data_plan; //流量套餐
  85. rt_uint32_t expiry_date; //到期时间
  86. int passWord; //初始密码
  87. char mqttcfg1[64]; //
  88. char mqttcfg2[64]; //
  89. char csq[8]; //信号强度
  90. char net[8]; //网络
  91. char sim[8]; //SIM卡
  92. char gps[8]; //定位类型
  93. char tempture[12]; //温度
  94. char humidity[12]; //湿度
  95. char driver[64]; //版本
  96. char driver_4g[64]; //4g版本
  97. char driver_bl[64]; //BL版本
  98. char driver_compile[64]; //BL编译时间
  99. char project[32]; //project,用于判断升级
  100. char lng[32]; //经度
  101. char lat[32]; //纬度
  102. char stamp[32]; //系统时间
  103. char fuse_voltage[32]; //保险丝电压
  104. char iccid[32]; //SIM卡ICCID
  105. char imei[32]; //IMEI,唯一ID
  106. char *power; //功率
  107. char *voltage; //电池电压
  108. }Device_Status_typedef;
  109. /************************************************/
  110. #define ON 1
  111. #define OFF 0
  112. #define LED0_PIN GET_PIN(B, 3)
  113. #define Beep GET_PIN(B, 4)
  114. #define OPEN 0x02
  115. #define CLOSE 0x03
  116. /************************************************/
  117. //光控
  118. #define LIGHT_PIN GET_PIN(C,0)
  119. //雨控
  120. #define RAIN_PIN GET_PIN(C,1)
  121. //加热
  122. #define Heat_Pin GET_PIN(B, 12)
  123. //采集/上仓门
  124. #define Collect_fan_R GET_PIN(C, 5)
  125. #define Collect_fan_L GET_PIN(C, 4)
  126. //下仓门
  127. #define C_DOWN_R GET_PIN(B,0)
  128. #define C_DOWN_L GET_PIN(B,1)
  129. //镇流器
  130. #define LAMP_SW GET_PIN(C,9)
  131. //震动电机
  132. #define SHAKE_SW GET_PIN(B,2)
  133. //补光
  134. #define LED_SW GET_PIN(A,15)
  135. //清扫
  136. #define CLEAR_R GET_PIN(C,7)
  137. #define CLEAR_L GET_PIN(C,8)
  138. //相机供电
  139. #define PHOTO GET_PIN(A,12)
  140. //路由器供电
  141. #define ROUTER GET_PIN(A,8)
  142. //RTU/DTU供电
  143. #define RTU_DTU GET_PIN(B,13)
  144. //海康相机拍照
  145. #define HK_TAKE GET_PIN(A,11)
  146. //清扫限位
  147. #define CLEAR_R_LIMIT GET_PIN(C,13)
  148. #define CLEAR_L_LIMIT GET_PIN(B,9)
  149. /*****************************4.0定制多光源*********************************/
  150. #define LAMP_1_SW GET_PIN(B,10)
  151. #define LAMP_2_SW GET_PIN(B,11)
  152. /***************************高空测报灯*************************/
  153. //上仓门电机限位
  154. #define CTR_UPO_LIMIT GET_PIN(C,13)
  155. #define CTR_UPC_LIMIT GET_PIN(B,9)
  156. //下仓门电机限位
  157. #define CTR_DWO_LIMIT GET_PIN(B,5)
  158. #define CTR_DWC_LIMIT GET_PIN(B,8)
  159. //雨控电机限位,控制排水和落虫
  160. #define CTR_RO_LIMIT GET_PIN(B,15)
  161. #define CTR_RC_LIMIT GET_PIN(C,6)
  162. /******************************吸虫塔*********************************/
  163. #define HK_5000W_P GET_PIN(B, 12)
  164. #define ROUTER_P GET_PIN(B,10)
  165. #define LED_P GET_PIN(B,11)
  166. #define PC7_TIM3_CH 2
  167. #define PC8_TIM3_CH 3
  168. #define PB1_TIM3_CH 4
  169. #define MOTOR1_CTR_PIN GET_PIN(C,9) //吸虫电机IO
  170. #define MOTOR2_CTR_PIN GET_PIN(B,2) //吸附电机IO
  171. #define MOTOR_CR_PIN GET_PIN(C,7)
  172. #define MOTOR_CL_PIN GET_PIN(C,8)
  173. #define MOTOR_C_LIMIT GET_PIN(C,13) //卷带限位
  174. void ctr_JD_Clear(void);
  175. uint8_t ctr_Motor_xichong(uint8_t status_ws);
  176. uint8_t ctr_Motor_xifu(uint8_t status_ws);
  177. /***************************************************************/
  178. /***************************************************************/
  179. uint8_t ctr_Heat(uint8_t status_heat); //加热
  180. uint8_t ctr_cangmen_up(uint8_t status_up); //上仓门
  181. uint8_t ctr_cangmen_down(uint8_t status_down); //下仓门
  182. uint8_t ctr_lamp(uint8_t status_lamp,uint8_t lamp_num); //镇流器
  183. uint8_t ctr_shake(uint8_t status_shake,uint16_t shake_sec); //震动
  184. uint8_t ctr_clear(uint16_t status_clear); //清扫
  185. void ctr_TG_Clear(uint16_t clear_timeout); //清扫2
  186. uint8_t ctr_led(uint8_t status_led); //补光灯
  187. void calorstat(uint16_t heat_time); //恒温
  188. void ctr_router(uint8_t status_router); //路由器
  189. void turnzp(void); //转仓
  190. void Hk_Take_io(void); //触发拍照
  191. void HK_TakePhoto(void); //拍照
  192. void ctr_photo(uint8_t status_photo);
  193. void ctr_RTU_DTU(uint8_t status_rtu);
  194. void ctr_DTU_Power(uint8_t DTU_Power);
  195. void HardWare_Init(uint8_t boot); //初始化
  196. void HardWare_Check(uint8_t boot); //自检
  197. void ResetInit(void); //上电复位
  198. void SunTest(void); //光控测试
  199. /*****************************************************/
  200. void WorkTask_XCT(void);
  201. /****************************************************/
  202. void WorkCheck(void); //工作检测
  203. void WorkTask(void); //工作任务
  204. //
  205. //线程
  206. int Control_clear(void);
  207. int Workstatus_check(void);
  208. int Work_Loop_Task(void);
  209. #endif /* APPLICATIONS_INC_CONTROL_H_ */