CBD_SY/Application_SY2/applications/beep.c

/*
 * Copyright (c) 2006-2020, RT-Thread Development Team
 *
 * SPDX-License-Identifier: Apache-2.0
 *
 * Change Logs:
 * Date           Author       Notes
 * 2020-05-23     Administrator       the first version
 */
#include <rtdevice.h> //使用 RT-Thread 的设备需要包含此头文件
#include <beep.h>
#include <control.h>
#include "hmi.h"

Device_Status_typedef device_status;

struct rt_device_pwm *pwm_device = RT_NULL; // 定义 pwm 设备指针
struct rt_device_pwm *pwm_tim8 = RT_NULL;   // 定义 pwm 设备指针
/*初始化蜂鸣器*/
int beep_init(void)
{
    /*查找PWM设备*/
    pwm_device = (struct rt_device_pwm *)rt_device_find(BEEP_PWM_DEVICE);
    if (pwm_device == RT_NULL)
    {
        rt_kprintf("pwm device %s not found!\n", BEEP_PWM_DEVICE);
        return -RT_ERROR;
    }
    return 0;
}
/*打开蜂鸣器*/
int pwm_on(uint8_t pwn_ch, rt_uint32_t pwm_freq)
{
    rt_pwm_set(pwm_device, pwn_ch, pwm_freq, pwm_freq / 2);
    rt_pwm_enable(pwm_device, pwn_ch); // 使能蜂鸣器对应的 PWM 通道
    return 0;
}
/*关闭蜂鸣器*/
int pwm_off(uint8_t pwn_ch, rt_uint32_t pwm_freq)
{
    rt_pwm_set(pwm_device, pwn_ch, pwm_freq, 0);
    rt_pwm_disable(pwm_device, pwn_ch); // 使能蜂鸣器对应的 PWM 通道
    return 0;
}
int pwm8_init(void)
{
    pwm_tim8 = (struct rt_device_pwm *)rt_device_find("pwm8");
    if (pwm_tim8 == RT_NULL)
    {
        rt_kprintf("pwm device pwm8 not found!\n");
        return -RT_ERROR;
    }
    return 0;
}
/*打开蜂鸣器*/
int beep_on(void)
{
    rt_pwm_enable(pwm_device, BEEP_PWM_CH); // 使能蜂鸣器对应的 PWM 通道
    return 0;
}
/*关闭蜂鸣器*/
int beep_off(void)
{
    rt_pwm_disable(pwm_device, BEEP_PWM_CH); // 失能蜂鸣器对应的 PWM 通道
    return 0;
}
/*在蜂鸣器设定函数里需要设定 蜂鸣器的频率和音量。PWM 设备设定的 API 是设定 周期 和 脉宽 的，
 * 因此我们需要转换一下，将频率装换成周期，将音量大小（占空比）转换成脉宽。这里的周期的单位是 ns，
 * 因此转换成的 秒 之后还要乘以 10^9 。由于无源蜂鸣器一般是低电平触发的，因此音量越大对应的脉宽就要越小。
 * 然后，将转换后的数据传入 rt_pwm_set 来设置 PWM 设备的参数。
 *
 */
void beep_set(uint32_t freq, uint32_t volume)
{

    rt_uint32_t period, pulse;
    beep_init();
    /* 将频率转化为周期 周期单位:ns 频率单位:HZ */
    // period = 1000000000 / freq;  //unit:ns 1/HZ*10^9 = ns
    period = freq; /* 周期为0.5ms，单位为纳秒500000ns-200k */
    /* 根据声音大小计算占空比 蜂鸣器低电平触发 */
    pulse = volume; // 5000

    /* 利用 PWM API 设定 周期和占空比 */
    rt_pwm_set(pwm_device, BEEP_PWM_CH, period, pulse); // channel,period,pulse
    rt_pwm_enable(pwm_device, BEEP_PWM_CH);
}
void Beep_Tip(uint16_t volnum)
{
    rt_pin_mode(Beep, PIN_MODE_OUTPUT);
    rt_pin_write(Beep, 1);
    rt_thread_mdelay(volnum);
    rt_pin_write(Beep, 0);
}
void Motor_Juandai(uint8_t on_off)
{
    pwm8_init();

    rt_pwm_set(pwm_tim8, PC7_TIM3_CH, 200000, 100000); // channel,period,pulse

    //
    if (on_off == ON)
    {
        rt_pwm_enable(pwm_tim8, PC7_TIM3_CH);
    }
    else
    {
        rt_pwm_disable(pwm_tim8, PC7_TIM3_CH);
    }
}
void Motor_Qingsao_R_PWM(uint8_t on_off)
{
    pwm8_init();
    rt_pwm_set(pwm_tim8, PC7_TIM3_CH, 200000, 150000); // channel,period,pulse
    if (on_off == ON)
    {
        rt_pwm_enable(pwm_tim8, PC7_TIM3_CH);
    }
    else
    {
        rt_pwm_disable(pwm_tim8, PC7_TIM3_CH);
    }
}
void Motor_Qingsao_L_PWM(uint8_t on_off)
{
    pwm8_init();
    rt_pwm_set(pwm_tim8, PC8_TIM3_CH, 200000, 150000); // channel,period,pulse
    if (on_off == ON)
    {
        rt_pwm_enable(pwm_tim8, PC8_TIM3_CH);
    }
    else
    {
        rt_pwm_disable(pwm_tim8, PC8_TIM3_CH);
    }
}
/**
 * @brief 风机调速
 *
 * @param on_off 开关
 * @param percent 百分比
 */
void CollFanSetPWM(uint8_t percent)
{
#define PWMMax 1000000

    if (percent < 0 || percent > 100)
    {
        return;
    }

    beep_set(PWMMax, PWMMax * percent / 100); // 驱动器使能
}

// void coll_set25(void)
//{
//     CollFanSetPWM( 25);
// }
//
// void coll_set50(void)
//{
//     CollFanSetPWM( 50);
// }
//
// void coll_set75(void)
//{
//     CollFanSetPWM( 75);
// }
//
// void coll_set100(void)
//{
//     CollFanSetPWM( 100);
// }
//
// void coll_setOFF(void)
//{
//     CollFanSetPWM(10);
// }
//
// MSH_CMD_EXPORT(coll_set25 , coll_set25);
// MSH_CMD_EXPORT(coll_set50 , coll_set50);
// MSH_CMD_EXPORT(coll_set75 , coll_set75);
// MSH_CMD_EXPORT(coll_set100 , coll_set100);
// MSH_CMD_EXPORT(coll_setOFF , coll_setOFF);

void Motor_shake(uint8_t status_shake, uint16_t shake_sec)
{
    beep_init();
    rt_pwm_set(pwm_device, PB1_TIM3_CH, 200000, 150000); // channel,period,pulse
    if (status_shake == ON)
    {
        rt_pwm_enable(pwm_device, PB1_TIM3_CH);
        if (shake_sec != 0)
        {
            rt_thread_delay(shake_sec * 1000);
            rt_pwm_disable(pwm_device, PB1_TIM3_CH);
            HMI_WRITE("cangWei.switchShake.val=%d", 0);
        }
    }
    else
    {
        rt_pwm_disable(pwm_device, PB1_TIM3_CH);
        HMI_WRITE("cangWei.switchShake.val=%d", 0);
    }
}